LBC22520ST (02) LG Refrigerator - Instructions

Part Select folks are very professional & courteous. They can only identify the replacement I needed based on data from LG. The data is WRONG. LG should be billed by Parts Select for their valuable time & shipping expenses. What I did was take the old shelf assy with rails & insert 2 each 1/4 - 20 threaded rods into existing holes in the rear of the shelf with nuts & lock washers on the inside & outside of each rail to stabilize it. It facilitated adjustment required to keep the rails parallel so the meat box would be secure. 85 year old guys shouldn't have to do this. LG should do a better job of servicing their product throughout its anticipated life expectancy. They should also send me the proper part.

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

Used a screwdriver to remove covers. Used a blow dryer to defrost coil in freezer. Cut zip tie and removed old controller assembly. Inserted new controller assembly and secured with zip tie. It took 24 hours for the fridge to cool completely. Now it works fine.

Ordered new part, which was crisper frame. Removed old frame and replaced it. Cleaned crisper glass and set in place.

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.

Pull off the grill cover and remove the 2 screws from the old part and simply screw in the new part. Don’t lose the screws there are no new ones with the new part. Replace cover.

1. Pull out the old gasket & push in the new one!

2. Pop out the light assembly with a screwdriver, disconnect the wire bracket, (the hardest part so I used pliers to grip the plastic) and connect the new one...pay attention to the direction to put it back in the space and you’re done! IF I CAN DO IT, YOU CAN DO IT! (Also check you tube videos for accurate instructions & correct terminology!!!)

Just slid out the broken drawer and slid in the new one. The web site was very user friendly and my drawer arrive in only a few days. THANK YOU SO MUCH!!!!

Went on line to see how difficult it would be to replace the valve. Through Google there was a video which showed in exact detail how to remove and replace the valve. Then went on line to find the replacement part which was readily available. The only problem was that the connection on the valve where the fill water enters the valve was larger than the old valve. To fix that I went to a local Ace hardware store and found a nut that would fit the valve connection. Also don't forget to use a compression ring to keep the fill line secured when replaced.
Over all it was very simple and was in my "pay grade"

Followed instructions online

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

As much as I am a hands on person, I did not do the installation myself. A friend who was visiting offer to do for me, and I simply did not refuse the offer. In my perception it really seems quite easy, a job that that I could do myself with ease.