LAT8234ABE Maytag Washer - Instructions

A tension sping on the motor broke, smoking the drive belt.
step1...remove front of the washer to access spring, tip washer back & prop on short 2 x 4 board. 5 minutes
step 2... remove one end of pump belt to get new bely up to drive pulley put on belt using fingers only & replaced the end of the pump belt....2 minutes

step 3...put new spring under motor & hook one end in attaching hole on motor, reach through with pliers to grasp spring to pull end to attach spot on base...1 minute

It took longer to open up the washer front & prop it up that it took to repair it. This is a siper easy repair!

Replaced the lid switch assembly. The pictures were very helpful. Very easy to replace. Saved at least $150 doing it myself.

I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.

Turned off water supply and disconnected hoses. Removed rear cover where water valve was located. Marked and unplugged wires to valve along with interior hose connected to valve. Unscrewed two screws holding valve to rear cover. Installed new valve with all the above procedures in reverse. Very easy repair that saved us slot of money in service call fees!

I simply took the old switch out and put in the new one. The part arrived very qickly and the website was super easy to use.
thank you so much!

I used a 1/4 inch socket to remove the agitator.Used a small screw driver to remove clip. Then I lifted the washer off the shaft with a magnet. Pried out the old seal with a screwdriver. This exposes the top of the tub bearing. I applied some 80-90 differential grease to the top of the bearing, pressed in new seal, installed other parts and noise gone. It sounds like a new washer. I'm glad I found you guys.

There is one good description already posted. I would add:1)If the the nut holding the inner tub doesn't loosen easily just split it with a chisel and don't waste time. 2)Don't order extra washers to remount the outer tub, they come with the bearing! 3)While disassembled I ran the spindle on spin to make sure the brake assemlby wasn't the problem. It ran quietly and smoothly. 4)The inner bearing sleeve was stuck on the spindle and didn't want to free up. I used a rotary tool to cut a groove in the old bearing sleeve then chiseled on the groove edge and it split nicely. It was very brittle. The washer seems to work well now. Next time I see a leak I am going to repair it right away!

Removed the knob on the timer. Removed the 4 screws on top of the machine. Removed the two screws with nut driver for the timer. Replaced the timer and the two screws that hold it. Plugged in the electrical socket to the timer. Put the face plate back into position and replaced the 4 screws, Put the control knob and plate back on and tried it. Worked great!!

First I removed the two screws that held the front panel in place. Then I determined that the belt for the pump had fallen off because the drive belt was worn (and inverted) and a piece was hanging off and causing the pump belt to slip off the motor. I replaced the belt for the pump (Temporarily) to allow the tub to drain.

I replaced both belts with new belts and returned the front panel. The process took 15 minutes due to the necessity of explaining the proper use of tools to a neighbor child and allowing him to assist (required for the completion of one of his Cub Scout requirements).

I went to a major appliance part outlet in my area...they told me that they didn't make the parts in the USA anymore. I found your website, ordered the parts, installed them in less than 15 minutes and now the washer works great. I would recommend your website to anyone... thank you

1st We pulled the washing machine from the wall and unplugged it. 2nd We tilted the maching back against the wall so that we could see all the pullies. 3rd. We removed the two screws that afix the front panel on the lower part of the washing machine and removed the panel. 4th We removed both belts and put new belts on. 5th We put all parts back in place and plugged maching back in, slide it back in place. 6th It worked like a charm and I proceeded to wash 3 loads of laundry that evening. The only tool we needed was the phillips head screw drive to take off the front panel. It took us 5 minutes to fix the machine.

The hardest part was figuring out how to get the front panel off of the washer. Once that was done, the pump came off easy.... 3 screws attached it to the bottom panel and 2 hose had to be disconnected. Putting the new one in was easy.

I turned off the water at the main water inlet. I then removed the hose connections to the valve inlet. I removed the one screw on the plate pulling allowing me to pull the plate out from the washer body. I then removed the wires connected to the old valve placing them on the new valve (so not to be confused). I took off the small hose clamp attached to the valve. I removed the valve from the plate and attached the new valve placing the a new hose lamp on the hose (wires were already attached) screwed back to the plate in the washer body connecting the water lines and turned the water on at the main valve. I did have to run to the hardware store for the small hose clamp but that was my choice to replace the one that was existing. The washer now works like it is new.

Wish there was a video. I am above average handy but this one- I might just pay someone next time...The tape on the threads was a great tip but took a while to understand what they meant by putting tape on the threads. Scraping off the old pads is easy for the front one but the back pad and a half is so hard to reach to really get it cleaned. Bruised and cut knuckles on that one. Then not having the glue for the pads was a surprise and you have to get a good contact type cement that sets in 10-15 minutes or you will be waiting hours to put it back together. It was easy to put the first spring on, then the second and third got harder and harder.

Well, I figured out a couple of things during this process. #1 The Washer was smoking. It had happened before (a sock got suck between the basket and the tub) so I assumed that happened again. I couldn't see anything in that space this time, so I dissasbemled the washer to see if any clothing was there. Relatively easy once finding the screws to remove the front panel. #2 What I found was a sock in the pump box. I disconnected the hoses and removed it, saw nothing between the basket and tub and ran it to see if problem corrected itself. It still was smoking. That is when I checked the belts, #3 first the pump belt, replaced it, very easy, just pulled the old one off, and wheeled the new one on. It still was smoking, #4 so I replaced the drive belt, very easy and the same as the pump belt. It still was smoking so I lubed the wheels for the belts, and #5 cleaned the residual rubber around the wheel from the old, fried, dry rotted drive belt. No more smoke!!! However #6 remember to leave space between the basket and the top of the tub, as when I put the washer back together the basket didn't spin. I removed the top and ran the spin cycle, it spun fine, reconnected and it didn't spin, the tub top was touching the basket, that's when I relized the top was on too tight. I reattached and left about 1/4 in of space and all is well now.