LAT4915AAE Maytag Washer - Overview

Diagrams for LAT4915AAE

See every part. Know exactly what you need.

Parts for the LAT4915AAE

View More

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Belt Kit – Part Number: 12112425
$50.55
In Stock
Belt Kit
★★★★★
★★★★★
(45)
Part #12112425
This kit includes both the drive belt and the pump belt which are both "V" shaped.
Mounting Stem/Tub Seal Kit – Part Number: 6-2095720
No Longer Available
Mounting Stem/Tub Seal Kit
★★★★★
★★★★★
(13)
Part #6-2095720
This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.
Screw – Part Number: W11233072
$30.40
In Stock
Screw
★★★★★
★★★★★
(5)
Part #W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
Tub Bearing Kit – Part Number: 6-2040130
$97.91
In Stock
Tub Bearing Kit
★★★★★
★★★★★
(4)
Part #6-2040130
This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.
Drain Pump – Part Number: WP6-2022030
No Longer Available
Drain Pump
★★★★★
★★★★★
(13)
Part #WP6-2022030
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
Damper Pad Kit – Part Number: 203956
$65.23
In Stock
Damper Pad Kit
★★★★★
★★★★★
(9)
Part #203956
This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.
Lid Switch Assembly – Part Number: WP22001682
No Longer Available
Lid Switch Assembly
★★★★★
★★★★★
(9)
Part #WP22001682
This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
Lid Check Switch – Part Number: WP207166
$58.25
In Stock
Lid Check Switch
★★★★★
★★★★★
(11)
Part #WP207166
This is used to start your washer once the desired water level is reached.
Lid Switch – Part Number: W10820036
$33.28
In Stock
Lid Switch
★★★★★
★★★★★
(7)
Part #W10820036
Keep your washer or dryer running safely with this easy-to-install lid or door switch kit. It stops the machine from working when the door is open, helping prevent spills and accidents. Compatible with many models, this small but important part fits neatly inside your appliance and comes with everything you need for installation. Just unplug your machine, swap out the old switch, and you're good to go. It’s about 2.5 inches long and blends in with most interiors.
Read less
Washer Hose Clamp – Part Number: WP596669
$11.52
In Stock
Washer Hose Clamp
Part #WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
Heat Resistant Adhesive – Part Number: W10841140
$29.65
In Stock
Heat Resistant Adhesive
★★★★★
★★★★★
(1)
Part #W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.
Water Inlet Valve – Part Number: WP22001274
$191.69
In Stock
Water Inlet Valve
★★★★★
★★★★★
(9)
Part #WP22001274
This washing machine water inlet valve has two ports for water to enter. This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
View More

Questions And Answers for LAT4915AAE

Ask our experts a question about this model and we'll get back to you as soon as possible!

We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
David - For model number LAT4915AAE
February 4, 2020
I replaced the washer timer and it appears to work fine but keeps blowing the 1 amp fuse located in the fuse block part number ps2017400. Any ideas? Thanks
Chris Boyle Profile
Hello and thank you for writing. It is possible that the fuse itself is faulty, you should check it with a multimeter and replace if defective. We hope this helps. Please contact us anytime if you require further assistance.
$37.50
Special Order
Fuse Block
Was this helpful?
Thank you for voting!
David - For model number LAT4915AAE
February 4, 2020
I replaced the 1 amp several times, than tried 3 amp and it blew also. What would cause this? It appears to blow while it is operating.
Chris Boyle Profile
Hello David, Thank you for the question. In most cases it is due to a defective micro switch in the Lid Switch Assembly, PartSelect Number PS11739302. The fuse is connected to the lid switch which, in turn, tells the washer whether the lid is open or closed. We suggest replacing the Lid Switch. We hope this helps.
No Longer Available
Lid Switch Assembly
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the LAT4915AAE

How this model fails, and the parts that fix it.

Leaking
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Burning smell
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Will not drain
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Will not agitate
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Spins slowly
Fixed by
these parts
Fixing
Fixing
Show All
Spinning Issues
Fixed by
these parts
Fixing
Fixing
Show All
No hot or cold water
Fixed by
these parts
Fixing
Show All
Noisy
Fixed by
these parts
Fixing
Fixing
Show All
Shaking and Moving
Fixed by
these parts
Fixing
Fixing
Show All
Water Filling Issues
Fixed by
these parts
Fixing
Fixing
Fixing
Show All
Won’t Start
Fixed by
these parts
Fixing
Show All
Lid or door won’t close
Fixed by
these parts
Fixing
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
Fixing
Show All
Draining Issues
Fixed by
these parts
Fixing
Show All

Videos related to models starting with LAT4915AAE

View More

Watch our pros, then fix it yourself.

Replacing the Belt Kit

Replacing the Belt Kit

Replacing the Washer Hose Clamp

Replacing the Washer Hose Clamp

Replacing the Lid Switch Assembly

Replacing the Lid Switch Assembly

Replacing the Glide and Spring Kit

Replacing the Glide and Spring Kit

Replacing the Damper Pad Kit

Replacing the Damper Pad Kit

Replacing the Water Inlet Valve

Replacing the Water Inlet Valve

Replacing the Transmission Lower Lip Seal Repair Kit

Replacing the Transmission Lower Lip Seal Repair Kit

Replacing the Tub Bearing Kit

Replacing the Tub Bearing Kit

View More
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum would not drain and there was a banging noise when the drum spun
600 of 658 people found this instruction helpful.
  • Charles from Whitman, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Read less
Other Parts Used:
Belt Kit
Belt Kit
Was this helpful?
Thank you for voting!
water leaking from around center shaft below fixed tub
530 of 560 people found this instruction helpful.
  • douglas from bonita springs, FL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Socket set
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag wa shers, when I came across your site. By looking at your diagrams, I determined what parts I needed and ordered them. The parts arrived in 2 days, and I installed them. There were no leaks and it cost me under $70 (a repairman would have cost at least $250). The only thing I would recommend to those in similar situations, is to purchase a spanner wrench (your site does not sell, but others do). The stem seal and hub assembly is reverse threaded (clockwise to loosen) and is difficult to remove due to tight quarters in the tub.
Read less
Was this helpful?
Thank you for voting!
Leaking water
205 of 233 people found this instruction helpful.
  • Joseph from Plano, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.

So I got the model number and googled online. I found Partselect and they had every part I needed. Took me 10 minutes online to find the parts for my specific washer. I couldn't believe how easy it was. Parts came in two days...and this was right before Xmas.

Anyways, changing out the pump was simple. Took 5 minutes to get it off and put the new one in. I decided to change the hoses and elbow siphon break as well while I had the thing apart as those parts were old...but still working well.

Got the washer back together and the floor is dry as a bone. Perfect repair, really easy to do. Hardest part was figuring out how to get the front panel off.
Read less
Was this helpful?
Thank you for voting!
View More