Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 peoplefound this instruction helpful.
anthony from HAVELOCK, NC
Really Easy
15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
Ice Maker was not crushing ice properly
2 of 2 peoplefound this instruction helpful.
george from Albuquerque, NM
Really Easy
Less than 15 mins
Simply replaced the Ice Maker container
Was this helpful?
Thank you for voting!
Leaking water valve
2 of 2 peoplefound this instruction helpful.
Dan from BOURBONNAIS, IL
Really Easy
15 - 30 mins
Nutdriver, Wrench (Adjustable)
Removed old, installed new.
Was this helpful?
Thank you for voting!
POS fridge is constantly under repair.
2 of 2 peoplefound this instruction helpful.
Russell from COLLEGE STA, TX
Really Easy
30 - 60 mins
Screw drivers, Socket set
Understood the problem by removing the old dispenser first. That made me realize I also needed the shaft. Went online and matched up all the #’s and the repair went smoothly.
Water was leaking when ice maker or water dispenser was being used.
2 of 2 peoplefound this instruction helpful.
Don from Orlando, FL
Easy
1- 2 hours
Screw drivers
Looked for the same repair on line by model number. I found it, watched the repair, then used those instructions to complete the repair on my refrigerator. The disassembly and reassembly took longer than actually replacing the part. It now works beautifully with NO leaks.
Was this helpful?
Thank you for voting!
The rigth door does close tight
2 of 2 peoplefound this instruction helpful.
Jorge from ORLANDO, FL
Very Difficult
More than 2 hours
I ordered a gasket and follow the instructions, such as warm the gasket, to get it in the door using my fingers, but the door did not close titght enough. The problem could be something else. The initial problem is in there
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 peoplefound this instruction helpful.
dorotea from staten island, NY
Really Easy
Less than 15 mins
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 peoplefound this instruction helpful.
Thomas from Roseville, CA
Really Easy
Less than 15 mins
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 peoplefound this instruction helpful.
stu from richmond, VA
Easy
Less than 15 mins
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Freezer drawer light switch failure.
2 of 3 peoplefound this instruction helpful.
HARRY from FSTRVL TRVOSE, PA
Really Easy
Less than 15 mins
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into
... Read moretrim. Plug refrigerator into wall socket.
Read less
Was this helpful?
Thank you for voting!
One of the lights was out and all lights would blink
2 of 3 peoplefound this instruction helpful.
RONALD from WALL TOWNSHIP, NJ
Really Easy
Less than 15 mins
Replaced the light that was out. Problem fixed
Was this helpful?
Thank you for voting!
Agitator seized because of rust
2 of 3 peoplefound this instruction helpful.
Robert from FORT MYERS, FL
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
Replaced motor
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 peoplefound this instruction helpful.
Gail from Golden, CO
Really Easy
Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
The door switch was broken so the interior light would not come on.
2 of 3 peoplefound this instruction helpful.
Catherine from BROOMALL, PA
Easy
Less than 15 mins
Screw drivers
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and th
... Read moree new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
My Orders
