KHMS147HBL2 KitchenAid Microwave - Instructions

Very simple, just removed the screws and plates from the top of the microwave and reused the screws to secure the new piece.

Part came in 24 hrs w/ no special "fast shipping requested" . Old door pried off fairly easily using a stiff but thin butter knife. Putting new door on was easy but only with 2 people: one person holding the handle side open and the other handling the new door. Fit the new door on the hinge side first and slowly push top and bottom edges inward until clicks are heard as the individual hooks engage the frame. When done, go back along each top and bottom edge to be sure all hooks are engaged and no gaps occur btwn door and frame. Trying to do it alone with no one holding the door open and steady would have been difficult.

I was able to buy the mounting bracket for a very cheap price and was able to instill it in my kitchen with ease.
Thank you

I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next

All you have to do is unscrew the clamps, remove the broken plastic pieces of tabs, fit the new grille into the slots on the bottom and put the two screws through the clamps at the top.

Wonderful service, the part arrived 3 days later and it took 10 minutes to re-install the vent. By just remove 2 screw to take out the old part and re-installed the new one.

Washed the glass tray and put in the microwave oven. Easy..

Remove the two screws to the plastic vent strip at the top of the unit. That exposes a metal cover (upper right) held in place by two more screws. (Found that removing the screw holding the key panel in place and moving that out of the way made for more work room) Remove the metal cover. The HV diode (visible) on one end is secured to the chassis by a screw. The other end is fitted to the HV capacitor. So unscrew one end and pull the HV diode off the capacitor. The replacement fits on like the old one came off. Very simple repair. But it would be safe to short the capacitor terminals to the chassis first. Noticed that it appeared the sparking was caused by the HV diode's outer casing being worn by the asbestos covered wire next to it and laying against it. I made sure the two were not touching, before putting the covers back on. Also, the problem started with an occasional spark when the MW started. It quickly deteriorated to a full, non-stop electrical sparking. You can hear it, smell it, and see it through the top vent. You don't need to remove unit to work on it.

PartSelect website indicated replacing the high voltage power supply diode is the solution for "no heat" 99% of the time, but the diode was OK. There is more info at the website concerning the case of "loud buzzing and no heat" indicating the magnetron needs to be replaced. As an electrical engineer with knowledge of microwave components, this was also my best guess. However, getting to the magnetron is not the easiest job, but it's not impossible. You also have to be careful to bleed off any charge stored on the high voltage power supply capacitor. Luckily, I found my KitchenAid service manual tucked away inside the unit since I couldn't find it online.

I ordered another one and placed it inside the microwave. It works and fits perfectly. I received the order exactly as scheduled.

Unscrewed three screws and used putty knife to pry door cover off unscrew door handle put on new face plate and redo the three screws and clip back on oh you have to unclip the glass part and put on to the new face plate before putting on new door front to microwave

Rep knew exactly what I needed when I described where the part should go on my microwave - price great - shipping great - installed in seconds. Thank you!

First remove three screws on the handel side of the door,then use a thin blade [putty knife or butter knife to seperate the plastic colored face from the door very gently . You must pry up to seperate the catches of the door panel from the door. Work your way back to hinge side of door. Remove the handel from the panel [2 screws] then remove the protective outter glass,push back on clips and lift glass out. Reverse the proceedure the door panel snaps back on to the door easily

Removed two screws to that held the old bracket. Installed new part and replaced the screws. Very simple. About 10 minutes. The part cost about $38.00. A repairman charged my neighbor 100 + dollars for the part and plus installation for the exact same thing. I highly recommend Partselect.

Removed turntable
Place support ring in track
Place turntable on support ring.
Easy, peasy!