Models > KERS303BWH1 > Instructions

KERS303BWH1 KitchenAid Range - Instructions

All Instructions for the KERS303BWH1
61 - 75 of 105
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven heated really slow, no heat from the bottom of the oven
Very easy followed instructions from a youtube video.
Parts Used:
Bake Element
  • tim from KEENE, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
electrical short from oven light.
I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy
Parts Used:
SOCKT-LITE
  • William H. from morehead city, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Worn/Bulb Socket
It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.
Parts Used:
SOCKT-LITE
  • JOSEPH from COON RAPIDS, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven did not work
Unplugged the power cord and slid the oven out and took old parts out and installed new parts
Parts Used:
SWTCH-MEMB
  • Anne from LE CENTER, MN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element had burnt out
Unplugged stove-Removed oven door two screws held the oven bottom pan removed same to observe the element removed thre fasteners removed inspection cover on back of the oven pulled off two electric wires replaced element reassembled easy job
Parts Used:
Bake Element
  • Richard from HAMPSTEAD, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element failed
Unplug range, remove cover from back of range disconnect red wires from element spade connectors. Remove oven racks, remove two screws from back of bottom tray, and remove tray. Remove screw from element bracket and remove element. Install new element and repeat steps in reverse order. Done.
Parts Used:
Bake Element
  • Jeff from HOLLYWOOD, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old element burned up
Took out the bottom tray and the back cover panel, unplugged the old element and plugged the new one in and reassembled
Parts Used:
Bake Element
  • Doyce from AZLE, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove big burner was not regulating heat properly.
Removed back cover, replaced defective switch, had a little difficulty removing old switch harness. Othan than that a really easy fix.
Parts Used:
Inifinite Switch
  • Kenneth from PETERSBURG, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
range would not heat right
very easy watched the howto you gave
Parts Used:
Oven Sensor
  • bobby from HERSCHER, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dual burner right front not heating properly
Purchased new switch shut off breaker unscrew the back plate remove front knob and two screws that hold it on remove the two electrical clips from old switch then reinstall in reverse order. Also watched the youtube video before hand, great help!
Parts Used:
ELMNT-SURF
  • Eric from HUMBOLDT, SD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower element shorted out
Followed the video on this site.
Parts Used:
Bake Element
  • Stuart from CHARLES TOWN, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element burned out
There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.
Parts Used:
Bake Element
  • lou ann from MARTINSBURG, WV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electric burner element not working
Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair
Parts Used:
6" Surface Element, 1200 W
  • Ronald from The Villages, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
After watching the video, I said to my wife that this is a simple installation. However, I’m looking at the screws, I did not have the correct screwdriver to remove the screws. I had to go out and buy that. After that, it was not a problem.
I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.
Parts Used:
Bake Element
  • Tom from THE VILLAGES, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven wasn't heating up to temperature. Kept showing it was preheating but never got there.
We watched the excellent video and followed the steps. We're in our 70s which is why we needed a flashlight to see the screws in the oven! So if we can do it...
Parts Used:
Bake Element
  • Susan from NEWTON, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KERS303BWH1
61 - 75 of 105
Back to Top