All Installation Instructions for KitchenAid Range KERK807PSS00

Remove racks before self-cleaning

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

Parts Used:

Range Rack

Michael from Waxhaw, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

not needed

screwed in the new oven light

Parts Used:

Range Light Bulb (15w)

Peggie from Gresham, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

circuit breaker blew

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Parts Used:

Range Main Power Terminal Block

Richard from Sarasota, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Power block terminal failure

Ordered part needed. Much, much cheaper than purching a new range.

Parts Used:

Terminal Block

Leonard from Brazoria, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Duel Burner , Inside Burner Out

Removed burned out burner, replaced new burner tested works fine

Parts Used:

Dual Surface Element - 2500w/1200w

ROBERT from MOSINEE, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

When removing the warming drawer I did not read the instructions and broke the slide for the drawer. I removed the drawer without pressing the tabs which broke the right slide.

I removed the broken slide by removing 1 screw on the front slide and the back of the slide came out of the slot in the very back (no screws). I fitted the back of the slide into the slot and then replaced the screw on the front of slide. Extended the slides then I pressed the tabs on the drawer and replaced in onto the slides (left and right) . Closed drawer and finished! Very easy!

Parts Used:

Drawer Slide Rail (Right)

Deborah from Ashburn, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

replace two stove top burners

It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.

Parts Used:

Dual Surface Element - 2500w/1200w

Burner Element - Right Front

Howard from CHESHIRE, CT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

terminal block back of range shorted and burned

EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare

Parts Used:

Terminal Block

Louis from Grantsville, UT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Contractors on my home did not tighten nuts on terminal block when installing. This caused an arch across terminal burning up unit .

Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.

Parts Used:

Terminal Block

Robert from San Antonio, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Terminal Block was melted where the cord had came lose.

Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.

Parts Used:

Terminal Block

Louise from Humansville, MO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

2 burners burned out of flat top stove

I can't believe how easy this was to fix. 1. Unplug the stove. 2. remove the screws that hold the stove top in place. 3. pull the top up, unplug the electrical wires and unscrew the ground wire 4. remove the stove top and flip it over. 4. unscrew braces holding the burners in place. 5. with pliers, remove the wire connections between stove top and old burners 6. replace with new burners. 7. reattach everything. And you're done! Go brag to the neighbors about what you just did.

Parts Used:

Dual Surface Element - 2500w/1200w

Lacey from Raleigh, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

dual element burned out

A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.

Parts Used:

Dual Surface Element - 2500w/1200w

Edwin from Christoval, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Center of Front Burner not heating up

Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.

Parts Used:

Dual Surface Element - 2500w/1200w

Bob from Aberdeen, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Broil element was shorted out and not working.

Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.

Parts Used: