KERC500YBL4 KitchenAid Range - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

very easy

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Removed the element by using a basic screw driver...two screws. Detached the slip on wire attachments (don't know what they are called). Re-attached new element and screws. Very simple. I was hoping elements were a little cheaper, but I was impressed with the speed that Part Select delivered my new element. I'll use them again.

Replaced both rollers....Quick and Easy!!

TURNED OFF THE POWER TO THE RANGE, DISCONNECTED THE ELECTRIC PLUG. I unscrewed the element attached to the oven, disconnected the connectors. Reconnected the element and screwed the part back to the oven. EASIER THEN I THROUGHT.

It was difficult to reach the back of the oven inside to remove screws. I had to use an extended socket with a bit tip. When I tried to remove the element from the clips, the clips slid back inside the insulation at the back of the oven. I had to take the back panel off of the oven, push the clips through the opening and then I used a bag clip to hold them so they would not slide back into the opening. I could not lift the door off-too heavy- to get closer to the back of the oven to put the clips and screws back on so I laid the oven on its back after putting the back cover on. The oven door was so heavy then that I had to prop the oven door open with my 24 inch rolling pin. I then leaned down into the oven and managed to get the clips and the screws back in. I then put the oven upright again, plugged it in, then had to re-level the whole thing. I turned it on and it worked. This probably would have been easier if I were not 65 years old and had some help. I was not giving up though. I got it done.

removed the screws that secured the lower element. Disconnected the old element from wire contacts. Inserted the new element into the wire contacts.

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

Removed back panel on stove and found no continuity in bake element indicating a break in the element circuit. Also tested electrical supply up to the element and found that we had electricity up to the element when the oven was turned on. Went on line and ordered the bake element and it was on my doorstep in 48 hours. Remove 2 screws inside oven and disconnect wires from the rear and install new element and plug the 2 wires into it, replace rear panel ( 3screws) and turn electricity back on to the stove and you are back in business.

Remove two screws. Plug n play.