KEDS207BAL1 KitchenAid Range - Instructions

This is an easy fix. Just before the holidays, it was imperative that this appliance be in top shape. Since the door 'hung' wrong, it was determined that the hinge pin broke. Remove the 2 phillips head screws on the door and open the door to the to a 15 degree opening. This position allows you to slip the door off the hinge levers. Now that the door is off, replace the hinge pin and slip the retainer ring on with a screw driver blade to push it on the pin. Slide the door back on the levers and fasten the retainer screws. DONE!

1. Open door and place a nail in the small circle in each of the two side hinges. This step is crucial. It keeps the hinges from springing back into the oven when the door is removed.

2. Remove the 2 screws on the oven door at the top of each spring. Close the door until stopped by the 2 nails, then lift the door up and off the hinges.

3. Lay the door on a soft surface(some oven parts may be greasy), inside of the door face up, and remove the 5 screws holding the main two halves of the door together. Remove the top piece.

4. Remove the 4 screws that are under the insulation strips. This will damage the strips, but there is no other way. Just try to keep as much of the strip as you can.

5. Continue removing screws and layers of glass (ours had 3 inner layers)until you reach the inner most piece.

6. Replace the broken glass and then reverse the process to put everything back together.

Notes: We work slowly and methodically, so the whole process took us over an hour but we also took this opportunity to really clean every crack and crevasse that is normally hidden. All in all this was not a very hard job and worth doing it as a DYI project instead of calling a repair person.

First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges by removing the two final screws. Then the door could be layed flat on the floor and it was much easier to put in the insulation and glass pane.

The honeycomb filter in the vent was missing so I bought the entire vent cap.. Thought it attach with 2 screws from inside the oven.. BUT -- when you loosen the screws, it wouldn't drop.. Looked at the new part and saw that it attaches to the vent outside the oven as well.. So to replace this puppy, you have to pull the cabinet apart..

Left it for another day.. Hopefully no grease fires..

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

New ones fit perfectly, and looks beautiful!

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 minutes) after that.

This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartridge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.

Started out removing the old clip that didnt hold burner element down anymore. It was a bit rough, since i was taking off a rivet. I used the screwdriver to carefully wedge the edges of the rivet upward so that i could get the wire cutters underneath it enough to snap the head off. After some fanagling for about 20 minutes, i popped it off. The rest of the repair went like cake, and i am soooo thankful that the replacement part i ordered from you included a screw and a nut. Next time, if there is a next time, this repair could be done in 2 minutes. THANK YOU FOR SAVING THANKSGIVING AND A $100 REPAIRMAN SERVICE COST FOR A $10 PART!!!

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Remove burners using my hands and replace new burners using my hands.

I didn't. Don't know how to get to light bulb to change it for this specific model

Plugged in the new burner, which we received in one day.We were delighted with the quick service

Since I had to pay an $80 house call fee, I asked repairman to tell me the model number for the element, called Parts Select, ordered the element myself and saved my weekend of 17 hungry guests.
So, I guess you would say I paid $80 for a diagnosis; I think I really knew the problem and solution all along as I have ordered to-install stove top element before.