KDHE404DSS0 KitchenAid Dishwasher - Instructions

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

Following a utube video made it easy. Removed the outer cover of the door to expose latch. Two screws remove the latch, pay attention to how it was positioned and put the new one on and then replace the panel. But first turn off the electricity to the unit at the fuse box.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

Removed screws holding dishwasher in place. This dishwasher has one one the left and right side after you open the door hidden behind a plastic hole cover that you can pry out of place with a putty knife or some other thin tool. After this pull the dishwasher out about halfway and there are 4 screws on each side of the dishwasher (on the outside) that hold the top track assemble. Just unscrew these with the appropriate sized socket, remove the old track and screw in the new track. Super easy. Anybody can do this.

Not a difficult repair, but made more difficult than it should have been by KitchenAid's decision to attach the track from the outside,rather than the inside. Remove the top and bottom racks (top rack just lifts off its tracks). After turning off power, remove the trim panel below the door, then open the door and undo the screws holding the tabs at the top where the dw is attached to the underside of the countertop. Lower the adjustment legs at the bottom front with an adjustable or sized end wrench. Assuming enough slack in the supply and drain hoses and power supply line, just pull the dishwasher about halfway out which will give access to the bolts holding the track mounts. You'll have to pull back the insulation to access the bolts. Then with a nut driver or socket wrench remove the bolts, put the new track in place and bolt in. Actual replacement takes less than five minutes. All the prep work to get to the mounting bolts is most of the work. If you have to disconnect the hoses or power it's a bit more, but I didn't have to do that. I made the mistake of only ordering the one track that failed (outraged that I have to replace this after only 5 years or so and too cheap to buy both), but in retrospect, I can see that I should have bought both. The opposite side is not in great shape and will need to be replaced at some point.
Not a difficult repair-well within most people's skill level. But really KitchenAid - either design the track to last longer or make it easy to replace without pulling the dw out!

It was easy to remove the old parts by using a screwdriver to push in “tabs” that kept retainer clips in place. Once removed, it was a matter of easy assembly in reverse and then re-clip. It became clear that the problem was because a few tabs that click into the sliding track and worn to the point where they no longer retained a tight connection to the track causing the upper rack to tilt with weight to front or back. Sure, the parts are a bit pricey but not when compared to a repair visit or a new KitchenAid which otherwise was functioning perfectly.

First I removed everything off of the bottom of the dishwasher. Then I removed the main center piece that everything mounts to. Then I reinstalled the new center piece with the help of some evoo cooking spray (extra virgin olive oil) I sprayed it on the rubber seal to aid in getting that center piece installed without a battle. Then I reinstalled everything else in the reverse order that I removed it. The evoo cooking spray works wonders for more than just cooking !!!

Actually, I found a video on Youtube with excellent instructions once you got past the really simple stuff like disconnecting power and water and drain.
I would recommend just finding a fairly similar model on Youtube and follow their directions. It was really easy.

Open the washer door, remove old rinse aid cap. Place new cap into designated spot, screw into place.

Pulled off old seal found center of new seal and pushed new seal into channel that old seal came out of starting at top middle underneath the latch

put new hose on, very easy.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

Thought this would be much easier than it actually was. Long story short, ended up calling is an appliance professional to install the part.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.