KDDT207BBL9 KitchenAid Range - Instructions

easy enough, just remember the order if disassembly and reverse for instqllation

We looked at SEVERAL postings on this site. We ARE NOT DYIers. The descriptions on how to do this repair were super helpful. When we read that it only took 30-minutes and was easy, we thought, "Well, they haven't met us!" On the contrary, we got through this without one marital issue. It did take both of us and was kind of like a puzzle. It took us somewhere between 30-60 minutes. We left the door on and worked our way through screw by screw, panel by panel and "voila!" -- we were able to turn on the oven that night without it exploding!! Thank you Part Select and all of the DYIers that post on this site!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Just replaced them.

removed one screw lifted he brner took retainer off unpluged the igniter it had broken porcelen reversed the procedure everything worked fine

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

Remove the 3 Phillips screws along the bottom of the door, 2 screws on the inside and 2 screws on the top edge near the handle. Take off the outer door. Clean out the dust etc with a Vac. Tape the inner glass to the inside of the door so it doesn't slip loose later. Close the door. Remove the 4 screws under the foam to take off the middle window asm, not the 4 screws holding just the middle glass. Now when you remove this assembly the inner glass is not supported(this is why you taped it) so do not jar or lower the inner door yet. Now that the middle assembly is off support the inner glass with one hand and lower the door. Remove the tape and remove the glass. Now install the new glass being careful the gasket is in place. Reinstall everything in reverse.

Remove the door. This takes less than a minute. pull the door up and out. have a friend help you do this. Set it on a table and remove the outside panel screws and separate the outer face cover from the inner. this will expose the many glass window. the inner window has screws hidden under foam strips. these four screws must be removed to gain access to all other window panes. clean and replace as needed, then reassemble. Be carful not to drop the glass panels. also make sure that any insulation is reinstalled. Reinstall the door back into the spring loaded hinges. done

Had to screw off old terminal block & screw on new one

I read how two others had fixed thiers on this site. Put a nail in each hinge then lifted door strait up off hinges and laid it on kitchen table. removed 9 screws around door. Lift inner door up. remove 3 nut head screws on each side and lift that shield up and out. replaced glass and the put it all back to gether. saved my self a good 200.00 plus dollars. thank you soo much. I will be back if I need anything else..Brenda..

1. Open the oven door (about 4 inches) until it hits that first spot that it stays open by itself. 2. Put a pin or small screwdriver in the tiny hole in the hinges - this will keep them from snapping back and also make it easier to put the door back on. 3. Pull up on the door until it comes off the hinges. 4. Lay the door on the table with the inside down - remove the 2 screws from the top of the door and the 3 screws from the bottom - pull cover off and lay to the side. 5. Use nutdriver to remove next panel - they are located under the strip of foam along the sides, 2 on each side. 6. Use nutdriver to remove 6 screws around the pane of broken glass. 7. Replace glass then do steps in reverse to get the door back together. 8. Slide door back onto the hinges, remove the pin or small screwdrivers from hinges. Voila! New glass, no problem!

Just replaced with the same color-almond

followed the instructions u sent me

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

FIRST: I Shut off the circuit breaker to the oven. Then: 1. Removed convection-fan cover (it was partially blocking the bake-element screws). 2. Unscrewed 2 bake-element screws. 3. Pulled old bake element forward to expose connectors. 4. Disconnected both connectors and discarded the old element. 5.Connected the new element and pushed it in so that plate was flush against the back of the oven. 6. Re-installed the 2 element screws. 7. Re-installed convection-fan cover. LASTLY: Turned on the circuit breaker to the oven and baked a cake! IMPORTANT: The original screws can be very, very tight. When removing them, be sure to use a socket wrench or other tool that gets a firm grip on the hex heads, or you could round the corners of the heads, permanently damaging the screws.