KBFN502EBS05 KitchenAid Refrigerator - Instructions

Completely on my own. Neither the owner's manual nor the instructions with the filter are of any use.A two or three panel series of diagrams with description of the process in English could make it simple. The release and reattachment of the filter are a bit difficult and need to be described as such.

push button take old one off put cap on new one,push it back in.easiest thing ever.

popped out the old one and popped in the new one

It was very easy just popped the old one out the new one popped right back in done in about One min .

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.

Removed the old one and installed the new one

Removed old water filter by simply twisting the the cap that houses it at the bottom of the refrigerator and replaced with new water filter. No fuss, no muss! Very impressed. Also, I was quite pleased to have received the water filter that was designed specifically for the whirlpool model that I own. I expected to receive some generic-type model based upon the reasonable price that I paid. Kudos to partselect!

It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.

Pulled out the old filter with the push of a button, removed filter cover from frig, took covers off the end of new filter and pushed it into the slot replaced cover. Job done--1 minute.

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in

Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!

Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.

Tried to remove filter with no success, there were no instructions in the package. "googled" how to install whirlpool filter and found how to do it.

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

only tools needed were my husbands hands. easily removed old filter and replaced with new one.