JVM1190WYC02 General Electric Microwave - Instructions

so easy, but how do i turn light off?

Part recieved next day. thanks so much

My son=law did repair because I am elderly and it was necesary to remove the bottom plate of the microwave which I was unable to do. The microwave was installed in 1987 and I believe this was the first time to replace the bulbs. When my son removed them the bulb was diintergrated. That's how old they were. Once he was able to remove the underneath plate the repair was easy except for removing the old bulbs. I think that I could have done it myself but he was available and I am sure it was done much better. All in all the parts)bulbs) were correct and everything is workiin fine. This is a good place to order replacement parts. In fact I am going to order a new charcoal filter. He took the label off the old one and I am ordering the replacement. After all 1987 may have been a good year, but time for a new one. Mary

With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

removed the lens cover with one screw and replaced bulb

I use a chopstick to help get the belt under a piece of metal between the fan and the wheel that turn the belt. I thought I might have to get a new oven, but the belt replacement seems to have fixed the problem.

had to hire someone to install the replacement part.

remove cover-unplug wires from secondary switch-remove switch-snap in new switch-plug in wires-replace cover-works great. very easy to do.

I took instant pictures at each step to make sure I put the wires back correctly. Removed the front panel. Discharged the capacitor with a voltage meter. Removed parts in front of the magnetron. Removed and replaced the magnetron. Reassembled. Works find now. Small hands, a flashlight and a magnet (for dropped screws) would help. I did not need the pictures.

every thing is working, but no hot

First, there are three door operated switches in this model. The monitor sw, the secondary sw (both of these are on the bottom in the same bracket) and the door sensing sw on top. The door sensing and secondary switches are both N.O. and have the same part number (probably why you show just two switches). The monitor sw is N.C. and it was not my problem. The secondary sw was bad on my oven but I had replaced the door sensing sw (which wasn't bad) on a previous order and kept the old one so I used it to make the repair. All three switches can be accessed without removing the oven by removing the discharge louver (remove two flat head screws on top and slide the louver to the left) then carefully remove the control panel (one screw on top and lift out). The switches are held in place by a plastic tongue that fits into the rear mounting hole on the switch. I used a common screw driver with a small tip to gently lift the tongue and slide the switch out with needle nose pliers. The new switch just snaps back in. The switch holder bracket looks like it would be easily broken so be gentle. I don't know what the symptoms would be if either of the other switches were bad so I would recommend buying all three and you would have them if one of the others failed in the future. The information I gave on the switches came from a schematic I found inside the control box. Hope this is helpful.

Microwave would not turn on. Lights and fan worked fine. Before the microwave stopped completely, it would turn the microware fan on even when door was open. I read the reviews and they were exactly the same issue that others were facing. Once I opened the front panel and got to the switches it was easy to figure out which switch was bad as it was the one that was soft (When clicking it). It was hard to take it out though (it seemed stuck). So, I used a plier to yank it out. I put in the new switch and everything worked just great! I would like to thank other comments that were left on the site to make my task much easier. Thank you (to the commenters on PartsSelect), you not only saved me money, but also ensured that I learn about the microwave more and give me the confidence that I could fix it.

Unscrewed the grill, removed old filter. Inserted new filter. replaced the grill, screwed it in. The end. Oh washed the grill before replacing.

Followed suggestion by previous poster to remove bottom panel...facilitated process well

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.