Models > JVM1190BYC02 > Instructions

JVM1190BYC02 General Electric Microwave - Instructions

All Instructions for the JVM1190BYC02
76 - 90 of 97
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave came on when door open
Turn off main power bracker. Removed fan vent, removed control panel, disconnect leads to the three monitor switches. Replaced the secondary switch (top). Reversed procedures.
Parts Used:
Monitor Door Switch Secondary Door Switch
  • Barry from Navarre, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace Burned-out bulb; Install filter
Took out 3 screws total, cleaned accumulated grease off of inside parts, put bulb and filter in, closed up by re-installing 3 screws.
Parts Used:
Light Bulb - 40W 130V Charcoal Filter
  • Ron from Pleasanton, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Unit was not heating properly. loose fan belt was stretched and falling off the pully.
removed cover and replaced belt. very simple! Many thanks for your prompt service.
Parts Used:
Convection Fan Rubber Belt
  • Frances R. from Concord, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
over range top light bulbs burned out
My son had to replace the bulbs because the screw that holds the bulb shield was so tight that I couldn't remove it. It was too difficult for me to do it myself.
Parts Used:
Light Bulb - 40W 130V
  • Elaine from Pittsburgh, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
light bulb below the over burned out
Getting the old bulb out of the socket was not an easy job as the factory seals the base of the bulb to the socket and for what reason I do not know. The seal has to be broken away to remove the bulb. I broke the seal with a knife and then proceeded to unscrew the bulb. The bulb at that point shattered in my hand and I was left with just the base of the bulb stuck in the socket. it took much effort to be able to work loose the base with a needle nose pliers and much sweat. The installation however went very smooth and Part Select did a fine job of sending me the right part in a very short period of time. They are a great source for any appliance part needed.
Parts Used:
Light Bulb - 40W 130V
  • Raymond from Walnut Creek, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bad bulb
unscrewed cover, took old bulb out, screwed new bulb in.relaced cover.
Parts Used:
Light Bulb - 40W 130V
  • edward from schererville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light worked, timer and control pad worked, but no turntable, no heat, no noises of any sort, just didn't start up
It was a snap using the instructions given. The key is getting into the unit. I did have to use a multimeter to find the failed switch since there are two of that type.
Parts Used:
Secondary Door Switch
  • Timothy from Middletown, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
lights under microwave (that we use as a kitchen night light went out.
undid plate exposing bulbs. Bulbs were blown to the extent that I could not see the size or wattage. Went to website, got the data ... including how to find the model and serial number plate, entered the info, looked at the exploded drawing, ordered 2 new bulbs and 3 days later they showed up at our door FedEX.
Parts Used:
Light Bulb - 40W 130V
  • JOHN from RIVERSIDE, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Rubber Fan Belt loose and slipping.
Removed upper face plate and fan cover with small cross point screw driver. Attached 24 inches of cord string loop to the driver end of the belt, lifted the belt off of the pulley, removed the belt from the fan, pulled the belt and cord string out. Attached the new belt to the cord and reversed the drill. Replaced the covers. It took me longer to write this note than it did to replace the belt.
Parts Used:
Convection Fan Rubber Belt
  • Marvin from Sun City West, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Unit would not come on.
removed access panal, found soft switch as discribed on your web site. removed and replaced.
Parts Used:
Secondary Door Switch
  • Phillip from Umatilla, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no lights
Remove light cover. Replace bulbs Note. Light bulbs are 40W,Too much heat for bulbs & sockets
Parts Used:
Light Bulb - 40W 130V
  • DON from CHEHALIS, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Over Stove Light Bulb Out
Took screw holding lens cover out, dropped cover down, unscrewed old bulb, screwed new bulb in socket. Screwed cover back in place. This is the third bulb in this socket, the other bulb is original.
Parts Used:
Light Bulb - 40W 130V
  • DALE from ST PETERSBURG, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light bulb burned out
Easy as can be. Removed one screw on the glass cover, removed two burned out bulbs and reinstalled two new bulbs, reinstalled the cover and all is well now. The best part - my 'supervisor' is happy that she can see to cook again!
Parts Used:
Light Bulb - 40W 130V
  • Bob from La Crescenta, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace micro/hood combo stove light
simply unscrewed protective lens cover, and swapped bulbs--these bulbs are great--last for years
Parts Used:
Light Bulb - 40W 130V
  • PATRICIA from ALEXANDRIA, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burn ed out bulbs
I removed light bulb cover shield,took out defective bulbs and replaced with new ones. 5minute repair
Parts Used:
Light Bulb - 40W 130V
  • DAVID from SUGAR HILL, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JVM1190BYC02
76 - 90 of 97