JTP25SH6SS General Electric Wall Oven - Instructions

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) Then I simply re-connected the replacement element and viola!

Turn power to oven off at the breaker.
Remove access panel to upper control panel.
With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.

Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.

Replaced old with new.

Very easy to remove the parts and to reassemble

slid the old ones out and slid the new ones in. done

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.

Turned off the oven power at the breaker. Removed the oven door by opening it all the way down. Flip the two metal tabs, one on each side, so the door releases. I used a flathead screwdriver to do it. Close door almost all the way and lift up to remove. Once the door is removed, there are two screws in the back of the oven connected to the heating element. Unscrew both screws. Gently pull out the heating element from the back wall. There are two terminals connected to wire clips holding the wiring in the back. disconnect, both terminals from the wire clips. Be careful not to pull on the wire or pull out from the wall too far. Connect to the new heating element to the same wire clips gently push it back into the wall reattached the two screws, reattached the door and turn on the breaker and test the heating element. I used YouTube to figure out how to disconnect and reconnect the door so that is an option.

I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

removed door on bottom oven; predrilled holes to match the trim package ordered; screwed trim to oak, popped on trim cover package and replaced bottom oven door. Done
Thanks for getting the parts to us so quickly!!

make sure to throw breaker and power is off of range, the elements still have power on them when range is off. Took door off, pulled racks out, pulled the two screws holding the element in place. Pull elements straight out and unplug the wires connecting to thr element and reverse the prosses.

Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.