Models > JMV9196CS2 > Instructions

JMV9196CS2 Whirlpool - Instructions

All Instructions for the JMV9196CS2
61 - 67 of 67
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clearing the clean code was the hardest part.
I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.
Parts Used:
Charcoal Filter
  • Wayne from New Berlin, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
in 2 yrs the charcoal filter had NEVER been changed and it was smelling horrible--so had to be done !
--simpley removed 2 screws, removed old filter--but had PLENTY of cleaning to do before putting in the new filter !My husband LOVES to cook and pan fry foods--it won't go that long before being replaced in the future!
Parts Used:
Charcoal Filter
  • carole from North Canton, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace filter
Time to replace the charcoal filter
Parts Used:
Charcoal Filter
  • Robert from Southfield, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace filters
For grease filter, just slipped it in outside area. For charcoal filter, unscrewed the top of microwave and replaced existing filter, then screwed back the top.
Parts Used:
Grease Filter Charcoal Filter
  • David F from BONITA SPRINGS, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Needed a clean filter
Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one
Parts Used:
Charcoal Filter
  • Ethel from New Berlin, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Reminder signal and message to change filter on microwave digital display.
Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.
Parts Used:
Charcoal Filter
  • Susan from North Olmsted, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burned out Halogen Bulb
Unscrewed light cover then inserted lights. When I called your company gave them the model Number they knew the exact part needed promptly mailed the replacement lights.
Parts Used:
Microwave Surface Light Bulb
  • Nancy from Clinton, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JMV9196CS2
61 - 67 of 67
Back to Top