JMV8208WS0 Jenn-Air Microwave - Instructions

All Instructions for the JMV8208WS0
31 - 45 of 91

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light burned out
7 of 12 people found this instruction helpful.
  • Terry from LINDSTROM, MN
  • Very Easy
  • Less than 15 mins
  • Screw drivers
One Phillip's screw to remove glass on bottom of unit. Pull old bulb out & insert new bulb. Replace glass & screw.
Was this helpful?
Thank you for voting!
Diode had burnt out
6 of 9 people found this instruction helpful.
  • Benny from OZAN, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Take off top facing over microwave using screwdriver also protection plate for diode and capaitor. Disconnect diode from frame, bracket to capacitor then remove, disconnect wires leaving diode on capacitor for right connection, replace, rewire done.
Was this helpful?
Thank you for voting!
Getter level with cabinet and use stud finder to make it easy.
5 of 6 people found this instruction helpful.
  • Terry from CENTRAL, IN
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
I measured. I leveled. I mounted hanging bracket and here's where it got tricky because you need two people to raise the microwave into position. I'd stack 2x4's In the back by the wall. I'd stackem in the front on the cabinet top then raise the back and add more. You get it front back front back until it's high enough to snag the bracket . Holes pre drilled raise it on up tighten bolts and poof you're done!! I did loosen the screws that pull the cabinets together and the bottom screw that holes the cabinet on one side. It didn't seem like it needed it the way it slipped in but maybe it slipped in because I did it. Only takes a minute. Use a minute here save an hour there. Go do it! Times a wastin!!
Was this helpful?
Thank you for voting!
Lights bulbs burned out
4 of 4 people found this instruction helpful.
  • Kat from Hudson, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Really easy for a 75-year old female; just spent more time reading the online manual than actually installing the light bulbs to find out where to access the light bulbs.
Was this helpful?
Thank you for voting!
Charcoal Filter clogged
7 of 13 people found this instruction helpful.
  • james from SHERRARD, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Remove top grill screws [2] remove grill replace filter put back together.
Was this helpful?
Thank you for voting!
Replace bulb under the microwave
5 of 8 people found this instruction helpful.
  • Verne from HENDERSONVLLE, NC
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Piece of cake. One screw to release the dropdown light diffuser. Just remember, the you're screwing the new bulb in from a reverse perspective. Also this site sends the correct part the first time.
Was this helpful?
Thank you for voting!
Maintenence
4 of 5 people found this instruction helpful.
  • Debra from IRVINE, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I first unplugged the microwave. I then unscrewed the 2 screws from the top grill. I had to be careful because the grill was cracked close to each screw. It was a little tricky to remove the grill. Had to tilt it down as I removed it, and make sure the microwave door was opened as wide as possible. Filters were placed as the old ones, wi th the metal part up I believe. A little tricky to get one of the filters to fit. Grill was replaced with care so as not to further Crack it. Kind of maneuvered grill back in place, getting right side in place first. I noticed there were several tabs on the grill that needed to be placed inside of the microwave body while reinstalling the grill. Once the grill was in place, the 2 screws were put in to hold the grill in place.
Was this helpful?
Thank you for voting!
Microwave turns on but did not heat
4 of 6 people found this instruction helpful.
  • John from Port Saint Lucie, FL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
Loosened but did not remove screws that held up microwave over range,removed grill on top by loosening screws that held grill in place.removed small mesh grill on right side of microwave, this gave me access to capacitor ,diode is connected from one lead of capacitor to a metal plate ground,Disccarged capacitor to ground by shorting ter minals to ground using a thick insulated screwdriver.Since the diode was screwed to the top of the metal plate I cut it out with a pair of side cutters .I then connected the new diode to the capacitor with my long nose pliers and groonded the other end to a more accessible part of the metal grounding plate.I then replaced all parts in reverse order.Works like a charm.
Was this helpful?
Thank you for voting!
Not heating up
4 of 6 people found this instruction helpful.
  • Michael from GLENDALE, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Remove “over the stove” unit. Remove unit shell case. Unscrew and disconnect diode. Replace diode. Re-assemble. Put unit back in place.
Was this helpful?
Thank you for voting!
needed microwave mounting bracket
3 of 3 people found this instruction helpful.
  • Patrick from MAYS LANDING, NJ
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
mounted bracket, case closed.
Was this helpful?
Thank you for voting!
Lights burned out
5 of 9 people found this instruction helpful.
  • Pat from GRAND ISLAND, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replaced bulbs easily.
Was this helpful?
Thank you for voting!
light bulb burned-out
13 of 34 people found this instruction helpful.
  • Pablo from Burlingame, CA
  • Really Easy
  • Less than 15 mins
screwed in new bulb
Was this helpful?
Thank you for voting!
Range light bulbs were burned out
3 of 4 people found this instruction helpful.
  • Barbara from MERIDIAN, ID
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
We needed a phillips head screw driver to remove the single screw holding the light bulb cover in place.
Removing the old bulbs was a little work, because they had come loose from the sockets. We unplugged the microwave, so we could grip the sockets with a tool. I think my husband used a needle nose plier for this.
The new bul bs screwed in easily, and then we refastened the light bulb cover with the phillips head screw driver.
Was this helpful?
Thank you for voting!
Exterior light bulb (PS2376034) broken off in socket. No access for pliers after glass cover removed.
3 of 4 people found this instruction helpful.
  • Alvin from HILTON HEAD, SC
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Unplug appliance. Remove total of 7 phillips screws from sides and front of bottom panel . Panel front drops down, remove one socket screw and socket. Now have access for lineman' s pliers to unscrew bulb base. Reinstall socket, replace bulb and 7 panel screws. Restore power.
Was this helpful?
Thank you for voting!
light bulb burnt out .
3 of 4 people found this instruction helpful.
  • DAN from CARPENTERSVLE, IL
  • Really Easy
  • 30 - 60 mins
Turn off power supply at breaker . Replace old bulb with new bulb .
Was this helpful?
Thank you for voting!
All Instructions for the JMV8208WS0
31 - 45 of 91