JKP18G4K4 General Electric Range - Instructions

First I shut off power to oven. Then I removed two screws from the back of the oven. Pulled elemeent out a couple of inches and diconnected from the power source. I removed the old unit and replaced it with the new one. Connected it to power source. Pushed element back into place and replaced the screws. Turn the power back on and turned on the oven. ....And there was HEAT!

I removed the two screws that hold the element in place; pulled the element out, disconnected the two wires held on by screws, replaced the element with a new one and reversed the procedure.

followed the existing guidelines from this site.

First turned power off for oven circuit at the breaker box then removed two screws that hold element in place. Pulled element out, tested for current, then removed two screws holding wires to element. Took old element from oven and inserted new element. Reattached wires with screws provided, and pushed element into opening. Replaced two screws securing element to back wall of oven. Turned the circuit breaker back on then checked to ensure the oven was working.

1. Turned the electricity off at the fuse box.
2. Took out the two metal screws holding the element to the oven back.
3. Unscrewed the screws holding the element coil, pulled the element out some and disconnected the two wires.
4. Replaced the old element with the new one.

The stove was new when we moved into our new home but opted to leave "our" stove in the basement until the one that came with the house had seen it's better days. The removal of the original element required the use an allen type of driver - it's removal was simple and the new element popped-into place without a problem and I refastened with the screws that came with the new element. The part arrived from PartSelect right on time, in good condition, and I would definitely do business with PartSelect again when I need to! My only complaint has nothing to do with PartSelect, it is the angle one must assume to refasten the part into place! Thank you, and I'll be back!

Removed the 2 screws that held element in place. Pulled the element out about 2 inches to disconect the wires. I then reattached the new element and replaced the screws holding the element in place.

Turned off power. Unscrewed two screws and pulled old element out of oven. Disconnected the two wires. Cleaned oven thoroughly, held new bake element with soft rag so as to not get fingerprints all over it. Wired new element and screwed it back into oven.

Baking sweet potatoes as I write, they will be delicious with my black-eyed peas and ham, a New Year's tradition in my neck of the woods.

first remomed screws of element, then removed screws to + & - connections, removed element & replaced with new one. Was very easy to find new part thanks to your easy partselect.Thanks Alan Collins

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

removed 4 screws and exchanged units put the 4 screws back in. about 10 min.

First I shut off power to the oven. Then, using a nut driver, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the two screws that make the electrical connection. Removed the old element and put in the new one.

Turned on power and ran the oven for a while to verify that it worked and to burn off any oils on the element.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Took the element out and put the new element in place. Used the original screws - not the ones came with new element - to secure the new element back in place. DONE.

removed and replaced element as required.thank to your website i was able to order the right part.now i have your site marked as favorite.thanks for making this easy for the non professional.

Our home was built in 1990 and has an original GE oven in it. When the bake element broke in half, I thought for sure it meant buying a new oven. When I looked on line and found Part Select.com, I was impressed to find the exact part I needed. I requested the part on Saturday, and it arrived on Tuesday. I installed the part on Saturday just in time for hosting our Super Bowl party and baking enchiladas! You guys saved the day! Thanks PartSelect!