JJW8530BA* Jenn-Air Range - Instructions

Remove trim piece from microwave above oven.
Remove 5 screws from inside oven below the display and control module
Lift out module and unplug three wire harnesses
Remove display and PCB from module.
Install in reverse

the glass front that houses the clock has four screw just above the door. Open the door to access the screws. Once the screws are out,
the glass front can be lifted up off the oven.
Instead of replacing the housing and the circuit board I removed the board from the housing and
and it snaps back into the old housing.

Actually, my brother was visiting and he removed the screws that held the panel in place, pulled it out and disconnected all the wires, noting how things were connected. Each set of wires was fairly idiosyncratic in shape and color, making it pretty obvious how they connected, but one tripped us by having several different ways that seemed to fit. After one negative trial, he found the right way to make it fit. We were amazed at how easy it really was.

This is a straight forward part replacement. You will need a phillips screw driver, a hex nut driver, a towel folded lengthwise, and a flash light. A second person's hands are helpful, but not necessary if you have a folded towel ready to use. First, shut off the electricity to the oven at the circuit breaker. Then open the oven door and remove the four phillips head screws under the oven control panel. The panel will then lift up and out easily. Highly recommended: have a second person present to help hold the control panel securely while you remove the three wire cable plugs from the existing electronic clock assembly to avoid scratching the plastic surface of the control panel against the sheet metal brackets that hold it in place. Alternatively, have a folded towel handy so that you may rest the control panel face down on the sheet metal brackets from which it was removed with the folded towel protecting it from being scratched by the metal brackets. Once the wire cable plugs have been removed, the control panel may be moved to a safer location with a soft surface (on a towel or other protective surface) to remove the four hex screws that hold the clock assembly to the control panel. Substitute the new part and replace the hex screws to hold in place. Attach the three wire cables to the new clock assembly, set the control panel back into it's brackets, and replace the four phillips screws to hold it firmly into place. Reset the circuit breaker to the oven. Reset the clock time, which will be 15 to 30 minutes slow (the time you had the power off). Done!

Very easy to replace. open oven door,
remove four screws holding oven control
cover, remove 4 1/2 in screws holding
display unit with a nut wrench, unplug
three connectors. intall new unit, replug
connectors and replace screw in reverse
order.

We followed the 63 year old lady's repair directions found on this website and were able to install the new display board in less than 15 minutes. As she said, it was really easy!

I unscrewed the cover on the oven. Used a socket to remove the electronic circuit board and unplug the electrical connectors. Then I plugged the new board in and reattached it.

Some of the connector prongs got bent in shipping I guess but I was able to straighten them.

I have a stacked microwave and oven. Removing the oven control panel was easy, removing the circuit board was easy, Replacing the wiring strips and board was easy. Reataching the control panel with the four screws was the hardest part., Gotta wirk upside down!! Saved about $200 doing it myself.

I followed other postings about this repair. It was easy. Open oven door, remove 4 screws that secure oven in the cabinet. Slide oven out a few inches. I thought it would be too heavy for me, but it wasn't. Remove 4 screws along the underside of where the clock panel sits. Have the oven door open, look up and you will see the four screws. Lift up and off for the glass front of the clock area. Undo the 4 sets of wire connections. They just snap in and out. Lay the glass on a towel, remove the clock assembly with a nut driver, replace with new clock assembly and reverse the instructions. When putting the glass panel back on, make sure you hook it over the top ledge. I missed that and after I replaced the 4 screws, I realized the top was not secure. Don't forget to kill the circuit breaker while working on this.

It was nice to be able to find this site and see that my problem was the same as others and they had all solved it with replacing the control module. So I ordered the part. Received it. Removed the 4 screws on the panel, then removed the connectors, then removed the bolts holding the control panel on the board. Replaced control panel and hooked it all back up. Very easy and was working in 15 minutes.

My friend actually replaced this but it was really quick and easy. If I'd had to do it myself, I think I could have because it came with the simpilist step-by-step directions! The best part of all was that I ordered it online on Monday and had it on Tuesday....during Christmas week!! Unbelievable service. Will definitely recommend this company to anyone needing any appliance parts!

Removed 4 screws that hold the clock assembly panel in place. Removed the defective part and replaced it with the new part. The wiring connectors were almost impossible to incorrectly connect.
Easy and saved $ 100

1. Remove 4 screws at the bottom of the control panel (above oven door) that hold it in place.
2. Pull the control panel away from oven and lift to remove.
3. Unplug two wire connectors to remove panel from oven.
4. Unplug two wire connectors from the clock panel. Used a putty knife to disengage the connector locking mechanism.
5. Remove 4 screws holding clock in place.
6-10. Installed new clock in reverse order of removal.

It was very easy, it took less than 10 minutes
just a few screws.

Turned off power to the oven
I removed the three screws holding the front panel on, then tilted it slightly and removed it. Then gently pulled the three wiring clips off the posts and set the panel down. Removed the 4 screws holing the dispay with a 1/4 " nutdriver and replaced the screen and reversed the procedure. Turned the power on and it worked!!