JIM158XYRS0 Jenn-Air Ice Maker - Instructions

part got here fast and I fixed it in no time. GREAT Thanks

Recently unemployed, we knew a repairman was out of the question. We opted to glue the broken tab,but I knew that would just be living a substandard rerpair so looked on line. Found our replacement part very easily and much to our surprise we had the part the next day, yes, the next day!! Looking at the new part gave us the confidence t ... Read more o pop out the old one without causing damage to our unit. It was a no brainer , pop out and plug in w/in 30 seconds. Small appliance repairmen are a minumum of 75.00 service fee plus parts. Our repair less than 20.00 less than 24 hrs. How good is that?

Gail Costa

Popped old one out with knife. exchanged power leads. Popped new switch in. Make sure to unplug refrigerator before you start!

I popped the switched out depressing the underside of the switch so that it could be removed.
I ordered the part.
Paid for normal shipping.
Received an order confirmation.
Received a shipping notification.
Received the part the next morning.
Open the part and attached the wires.
Pushed the switch int ... Read more o the hole and the process was done in less than 24 hours. I couldn't have been more pleased. The actual installation took less than 30 seconds.

plugged the two wires in and snapped the switch into it's socket.

unscrewed the old one! installed the new one! That simple. And I'm female, how easy was that!

shook bottle and painted waited a day and repeated

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source

The repair went just fine. Your instruction regarding using the wiring harness were clear. Most of all I am happy to not have to listen to a noisy motor all night.

as told per compter

I replaced the thermometer first and it started working again. I was convinced that the reason that it continued to break every 6mos was because no one had ever replaced the fan. The difficult part was getting to it. After trying to get in from the front and from the back I finally figured out that I had to take the bottom off and tilt i ... Read more t on its side. I was then able to get out the pin in the condenser and move it to the side. I could then reach the screws that held in the fan. I then decided to put the fan on the motor and when I was tapping it on with a hammer the back cracked. I attempted to fix it by taking apart the old motor and salvaging the parts but that didn't work. I had to buy another $85 part and take the whole thing apart again. It was easier the second time because I knew which screws and pins I had to remove and how to get to them. I very, very carefully tapped the fan onto the motor and now it is working fine. I will let you know if it is still working at Easter. If it is I will have done a better job than the 7or 8 repairmen who have fixed it in the past

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to ... Read more the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.

Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.