JGSP28SEN1SS General Electric Range - Instructions

There are 2 screws to remover to replace the element. That was the hard part as they were very stubborn to get out. I have to use a flexible bit and an impact driover to get them loose. Other than that, the replacement was smooth as silk !!

remove the oven door to remove the lower oven tray next remove the four 1/4 in. head screws from the burner cover to get access to the igniter remove the two 1/4 in.screws with small socket, wires must be pulled out from behind the oven rear wall to get access to the connector plug, disconnect and attach new connector to plug and tuck wires and plug back behind oven insulation reinstall screws in igniter bracket at this time i tried the oven,it lit , reinstall burner cover,oven tray and oven door .

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Removed racks, removed bottom cover ( slides out)- removed burner cover and burner- ignitor screws were both stripped where they attatch to burner so i just drilled them out and installed the new ignitor with two nut, bolt lock washer combos. Re-assembled and mamma was happy to bake again!

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Removed racks and inner oven casing. Had to slide oven out and disconnect power. The screws holding ignitor on the inside were stripped so that delayed us a bit. We used impact drill to remove other parts but socket set would work too. Fixed the problem and we were up and running in no time.

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part only coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.

Pull the old one put in the new one ... took about 20 minutes

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it fits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.