JGP932TEC1WW General Electric Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner would not light because spark was skiping to ground elsewhere
First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. I used new gashket and ignitor.
Parts Used:
-
David A from Spring, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range burners would not light
Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.
Parts Used:
-
Gregory from Washington, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner injet replacement
I needed a right front burner injet which is no longer made. On my cooktop I was able to move the left burner to the right and then ordered the left. Very easy to replace.
Parts Used:
-
Edward from NEPTUNE, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Yellow flame on large burner
Removed top grate. Removed burner head . replaced with new burner head. Replaced grate.Very simple replacement. Old burner head was warped with age.
Parts Used:
-
Charles from Glendale, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Parts Used:
-
Dana from LEEDS, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing ignitor
Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.
Parts Used:
-
Sam from Austin, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber grate foot failed
-
Gary from HENDERSONVLLE, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Grate foot is to big for the hole.
-
Harold from Broadalbin, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
very easy
-
ROBERT from CYPRESS, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
-
Chelagh from Fredericksburg, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
-
John from Tijeras, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Parts Used:
-
Gene from Simi Valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
1 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing grate foot.
-
Barbara J from Sweetwater, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
burner flame out of control
-
tom from san pedro, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
the grate foots came off
put it in but it keeps falling out. they're made narrower than my oven grate.
Parts Used:
-
Sandra from Watertown, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!