Models > JGP330BEK2BB > Instructions

JGP330BEK2BB General Electric Cooktop - Instructions

All Instructions for the JGP330BEK2BB
16 - 30 of 52
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Gas coke top wouldn't lite
First step is to turn off the electrical then disassemble the cook top. It is secured to pan by each of the burner mechanisms. Disconnect the spark wire from each porcelain drip pan. Separate the glass top from the pan. If it's stuck gently slide a putty knife int between the two to separate and carefully set the glass top aside. The spark module was a bit challenging in that the colors of the wires didn't match so if you aren't comfortable with electrical work I would get help. The module didn't fit the bracket so,I had to drill new holes and use self tapping screws to mount it. The other part part I intended to change was the spark igniter switch. Unfortunately the wiring was incompatible so I had to return that part. This top was sold by Kenmore but made by GE and is over 10 years old so I suspect an engineering change obsoleted my part. Overall the job wasn't that bad if you are reasonably mechanical..
Parts Used:
Spark Igniter Switch and Harness Assembly Spark Module - (4+0)
  • James from ABINGDON, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had uneven flames
Too easy a five year old could do it
Parts Used:
Burner Head - Large - 12K
  • Akshay from Bridgeton, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The eye would not light
Remove the existing burner and install the replacement.
Parts Used:
Burner Head - Large - 12K
  • Solomon A from COLLEGE PARK, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter constantly ticking ...
Unplug!!
Pull knobs
Pull burner centers
Unscrew the nut at the center of each burner
Tilt cover up revealing under burner controls
Remove old harness
Install new harness
Reassemble in reverse order
Plug in NO ticking
Parts Used:
Spark Igniter Switch and Harness Assembly
  • steve from BEAVERCREEK, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs had melted
Pulled out the old. put the new ones on. Easy
Parts Used:
Knob and Clip
  • Martha from DOWNERS GROVE, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Parts Used:
Grate Foot
  • Terry L from Puyallup, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold
Parts Used:
Grate Foot
  • Richard from Stratham, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Parts Used:
Spark Module - (4+0)
  • paul from las vegas, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Parts Used:
Top Electrode Mounting Clip
  • Dana from LEEDS, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniters would not turn off
Replaced starter switch harness as well as igniter module. Cost was around $70 for parts. Cheaper than a new cooktop.
Parts Used:
Spark Igniter Switch and Harness Assembly Spark Module - (4+0)
  • Paul from UPLAND, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas burners not heating evenly
remove old burner, put new in place
Parts Used:
Small Burner - 5K Burner Head - Large - 12K Burner Head - Medium - 9500
  • Juanita from GAINESVILLE, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Parts Used:
Grate Foot
  • Gary from HENDERSONVLLE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
IGNITER INOP
REMOVE GRILL AND TOP OF BURNERS. CLEAN GUNK OUT OF TORQUE SCREWS AND TRIED TO REMOVE TOP PLATE. FOUND IGNITERS ALSO NEED TO COME OUT, THEY HAD HEAVY DEPOSIT,
BE CAREFUL. ONCE I GOT THEM OUT, JOB WENT WELL. NOTE
MAKE SURE ALL CONNECTION ARE CLEANED BEFORE REASSEMBLY.
Parts Used:
Spark Igniter Switch and Harness Assembly Spark Module - (4+0) Knob and Clip
  • George from HUMBLE, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Parts Used:
Burner Head - Medium - 9500 Burner Head - Large - 12K
  • Mohammad from BARTLETT, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Parts Used:
Burner Head - Large - 12K Burner Head - Medium - 9500
  • Robert from SOUTH ELGIN, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JGP330BEK2BB
16 - 30 of 52
Back to Top