JGD8430ADS14 Jenn-Air Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Knobs on the new JennAir Range I just purchased started to melt and when they were called they did nothing about it. I had to call and get new knobs at my cost.
Very easy, just removed the old ones and the new ones just clicked on.
Parts Used:
-
Sherry from Mentor, OH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electronic ignitor malfunctioned
First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.
Parts Used:
-
Richard from Sherman Oaks, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Being dumb enough to buy Jenn-Air appliances
I removed the old knob and replaced with a new one from the plastic package. Biggest challenge: opening the new plastic package. It if very nice to know you have many of the parts I will need over the next 20 years.
Parts Used:
-
Brian from Rancho Mirage, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken stove knobs
-
Jacob V from Houston, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cracked knob
-
Charlie from Willis, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor sparking at bottom, not the top
Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!
Parts Used:
-
Edgar from COCKEYSVILLE, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner nob broken
-
John from Mesa, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken knobs
First I removed the old damaged knobs by pulling upward on the knobs. Then I replaced the damaged knobs with the new knobs being careful to align the male and female connection. After installation I tested each burner for proper operation. As a final test, I asked my wife for her opinion. We're happy!
Charles & Dorothy
Charles & Dorothy
Parts Used:
-
Charles from Grenada, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!
Voila!
Parts Used:
-
Aubrey from EADS, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter clicked but burner would not light
Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.
Parts Used:
-
Margaret from ROCHESTER, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs worn out, would not turn the post of the "D" switch.
Removed old knobs. Removed the metal insert from around the post from the old knobs with needle nose pliers. Installed new knobs. Easy fix.
Parts Used:
-
David from GUTHRIE, OK
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One was broken when bought house
-
Karen from FAIRMOUNT, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed use of penetrate lubrication
-
Juan J, from UNIVERSAL CTY, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs slipping
Remove old knobs and remove old grommets. Insert new grommets, install new knobs.
Parts Used:
-
CHARLES from SPRING HILL, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knobs for the cooktop burners did not fit so I have returned them and still do not have use of all burners due to lack of knobs
Could not put a square peg into a round hole....parts did not fit and I do not know how to find the model number but the knob has two flat sides.l....the knobs you sent did not.
Parts Used:
-
Pat from MCKINNEY, TX
-
Difficulty Level:Very Difficult
-
Total Repair Time:30 - 60 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!