All Installation Instructions for Cooktop JGC9430BDF

Ignitor sparking at bottom, not the top

Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!

Parts Used:

Burner Electrode

Edgar from COCKEYSVILLE, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electtrode

removed screws that hold burner in place lifted and removed wire connection, reversed attached wire replaced two screws job done,,,

Parts Used:

Burner Head with Electrode - Small

Glenn S from Edgewater, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the gas burner head needed to be rerplaced due to the sparker not functioning properly

Ordered a replacement, removed the old burner and installed the new one. Works perfectly.

Parts Used:

Large Burner Head

John L from FAIR OAKS, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed use of penetrate lubrication

Removed two screw securing wburner and disengage igniter.

Parts Used:

Large Burner Head

Juan J, from UNIVERSAL CTY, TX
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Electrode not working.

Removed two screws and slipped the electrode connection off. Then reserved the process.

Parts Used:

Burner Head with Electrode - Small

James from PRATTVILLE, AL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Auto igniter had gone bad.

Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!

Parts Used:

X-Large Burner Head with Electrode

Aubrey from EADS, TN
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Igniter clicked but burner would not light

Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.

Parts Used:

Screw, 8/18 x 3/8

Large Burner Head

Margaret from ROCHESTER, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I lost the cap

after I received the cap in the mail, I removed the grillwork and set the cap in place. then replaced the grill and my wife fixed my supper.

Parts Used:

Burner Cap - Medium

Bill from Rochester, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Ignitor cracked on 3 of my gas top buners

I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones

Parts Used:

Burner Electrode

james from neuvo, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The ignitor went out on one of the burners of the gas range

Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.

Parts Used:

Burner Electrode

Ed from Overland Park, KS
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Range would not light.

First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.

Parts Used:

Burner Electrode