All Installation Instructions for General Electric Range JGBS04PPM1WW

broken part

The key here was that I found the correcd part for an older kenmore oven and it was easily installed

Parts Used:

Double Burner Assembly

David from Warwick, RI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

We had to buy two dubble burner assemblies because one burner was out on each old assembley

The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.

Parts Used:

Double Burner Assembly

Alphonse from Glendale, AZ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter

Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.

Parts Used:

DEFLECTOR OVEN

Barry from Coventry, RI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The double burner assembly had years of gunk so the burn was not clean.

The old double burners lifted off. Before the new burner could be set down into place, the area had to be completely cleaned using a flat blade screwdriver and damp rag. This allowed the new burners to seat properly in place. That is it.

Parts Used:

Double Burner Assembly

Larry from Forestville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burners were not burning properly

Just removed the old and set in the new. Waalaa. All is well now. The web site, ordering, shipping and all was super easy.
Thank you

Parts Used:

Double Burner Assembly

Judy from Payson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Back burner not working

Lift stove top, rest it on the pop out holders on stove.
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]

Parts Used:

Double Burner Assembly

albert from La Veta, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One burner wouldn't light

Removed old and set inserted new

Parts Used:

Double Burner Assembly

Norton from Malta, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

gas flame flared and blackened pots; gas jets clogged

raised the range top so the supports locked in place. carefully lifted off the old burner assemblies. used a paper towel to remove any black soot from gas jets. opened the plastic package of the new burner assemblies, pulled out the new parts and carefully put them in place. turned on the flame to test... took less than 5 minutes to fix a problem that's been annoying for 3 years!!

Parts Used:

Double Burner Assembly

Patricia A from Newport, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

piolet light would not stay lit

R&R thermocoupel

Parts Used:

Oven Burner and Pilot Assembly

Donald from Buffalo, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench set

Was this instruction helpful to you?

Thank you for voting!

3 of 4 Burners would not light

Open the stove top pulled old burners out dropped new set in place. Theyclick right in NO TOOLS REQUIRED!!!!

Parts Used:

Double Burner Assembly

David from Cincinnati, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

oven door seal gasket broken.

removed old gasket and clips, replaced with new gasket that came with clips. easy. worked well.

Parts Used:

GASKET DOOR ASM

Frank from Ventura, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The oven door gasket was worn and didn't provide a good seal.

I use needle nose pliers to remove the old gasket tabs and clean the area with a scouring pad. Then I just lined the gasket up with the holes on the door and pushed the holding tab into the holds.Very easy and simple job.

Parts Used:

GASKET DOOR ASM

Willie from Selma, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

no racks to oven

Easily glide in.

Parts Used:

Oven Rack

Johnette from Baltimore, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Old dishwasher rack and silverware rack

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Parts Used:

Oven Rack