JFFCF72DKL05 Jenn-Air Refrigerator - Instructions

Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.

I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After r ... Read more eplacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.

Unscrew filter. Screw on filter bypass

I used “ Bruce from KIRKLAND, WA” instructions.

Without it, I may still be struggling to remove it. These are his notes summarized.

Remove both humidifier drawers
Remove the glass shelf
Remove the deli drawer and lid

To remove the end cap (either side) there is a plastic tab to push down on just ... Read more over halfway back and then you can slide the front of the end cap up and out.

THE PLASTIC TAB IS THE KEY!! ---^

To install the new end cap, reverse this process.

The trickiest part is then re-inserting the deli drawer and the lid.
Getting the lid onto the two axles was a bit of a struggle as the fit is very tight.

Huge thanks to Bruce from KIRKLAND, WA!!!

Ordered new fan motor
Got part took fridge apart
Result was the motor was running
The fan blade had come off the motor
Replaced the motor anyway and reinstalled the fan, working well

There have been two problems with closing the left door.

First, the flap did not engage with the stop at the top of the cabinet and so the door did not close properly. Fixed this by adding a shim to the cabinet stop to lower it by about 3/16 of an inch.

The second problem was that the left door flapper had somehow g ... Read more otten loose from its lower plastic clip. The solution to this was simply to remove the single screw in the flapper in the center where the electrical connector is, then re-attach the flapper with both clips properly engaged, and replace the screw to hold things fast..

No new parts were needed.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Remove the 2 screws that secure the flipper seal to the door. Slide the entire flipper seal up approximately 3/8ths of an inch. Disconnect wire connection. Reverse procedure to reinstall. Be sure flipper seal is pushed down enough to align screw holes before trying to reinstall the 2 screws.

Simply cut the water tube on both sides of connector and push in the new one.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
... Read more />Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Very easy to fix . It was harder to empty the contents out or the refrigerator than to repair . The diagrams on this site were very helpful in identified the part. and it was delivered in 5 days.

The Youtube Video was Extremely helpful--the model they worked on was a Whirlpool, and is held in with 1/4" machine screws. The KitchenAid is largely identical, but doesn't use screws. There is a plastic release you depress to free the Right Support from the cabinet. Otherwise, the process is identical to what's shown on the Youtube vi ... Read more deo. The Fridge "came with" when we bought the house, and we've already replaced the door seals using this website (another easy fix). Of course, when gently reinstalling the lid I snapped the pin on the Left Pantry Drawer support. So i've ordered that part too--i'll chalk it up to age/wear&Tear. The Left is much easier than the Right, as the Right Support has a sliding humidifier setting slide. So the Right is slightly more involved, but is also an easy fix. No tools required at all for either drawer support on the KitchenAid. Just be very patient and gentle as you re-install the drawer lid.