JES1750FS0 Jenn-Air Range - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

After part arrived I removed fan casing from the inside, then slid the range out and unplugged it. I unscrewed part from the back and put in the new part. Plugged range, turned on convection to test and it works properly now! Fan spins smoothly!

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical ... Read more connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

First, I shut off power to cooktop at breaker and double checked to make sure. Then I disconnected wiring and exhaust duct since the cooktop is a downdraft. After that was completed, I had to remove control knobs simply by pulling straight up. A neighbor helped me to lift the cooktop from the cabinet. After stabilizing the cooktop, I remo ... Read more ved the hex nuts holding the glass in place. Then the glass lifted off easily and I could access the bad element. I took pictures of the wiring before disconnecting the wires and installed the new element. Then I reversed the procedure to put the cooktop back in the cabinet, reconnecting the electric and exhaust. I flipped the breaker back on and the element was just like new...because it was!

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two s ... Read more crews and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

Video said to remove screws and lift stove top off, remove contacts and ground. My stove top was hinged and required me to lift and pivot stovetop up. The burners were anchored to the stove base not the top. I secured the topso that it would not drop down and proceeded with repair

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The ... Read more part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Your technician suggested that the control knob unit was defective. I ordered the part and after watching your video, I was able to make the repair

Two screws to remove glass top. 2 connectors to remove. Removed glass top and put it upside down. Remove 4 wires and 2 Phillips screws. Reverse steps.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

I located the model number. Then searched the problem on YouTube. I saw that it was most likely the infinite switch and was an easy fix, so I ordered the part from this site and replaced it following the directions on the video. It's now as good as new!

There is a good video on YouTube that shows exactly how to replace the bake element. Had mine fixed in 15 to 20 minutes. Saved me about $150 by not having to call repairman.

very expensive to buy the part but just tighten the screw intot eh predefined place.

Remove the range door. Look on YouTube. Remove 4 screws holding on the fan cover at the rear wall of the range. (This was a slide in range and I could not get to the back without a lot of extra work.) Remove the 3 screws holding the fan in place. Be care and handle the fan gently. Remove the fan by moving outward slightly. Be very ... Read more careful of the electrical connections on the back of the fan. There are 4. Tilt the assembly out from the top a couple of inches. Slide off the two wires to the heating element, lower the assembly down while keeping the bottom close to the range back wall. Slide off the two connection fan wires on the bottom. Be careful and do not over stress this plastic harness wire connection, it will break. Remove fan. Put the new one on. First slide on the harness connection at the bottom while holding the bottom of the fan close to the range back wall. Rotate up and hook the two element wires. Put the screws back in for the fan and cover. This is very sensitive work. Take you time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. ... Read more Thank you partselect and i would use them again in the future. billy