JES1450CFS2 Maytag Range - Instructions

Remove the range door. Look on YouTube. Remove 4 screws holding on the fan cover at the rear wall of the range. (This was a slide in range and I could not get to the back without a lot of extra work.) Remove the 3 screws holding the fan in place. Be care and handle the fan gently. Remove the fan by moving outward slightly. Be very ... Read more careful of the electrical connections on the back of the fan. There are 4. Tilt the assembly out from the top a couple of inches. Slide off the two wires to the heating element, lower the assembly down while keeping the bottom close to the range back wall. Slide off the two connection fan wires on the bottom. Be careful and do not over stress this plastic harness wire connection, it will break. Remove fan. Put the new one on. First slide on the harness connection at the bottom while holding the bottom of the fan close to the range back wall. Rotate up and hook the two element wires. Put the screws back in for the fan and cover. This is very sensitive work. Take you time.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), ... Read more which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I have tried to call, but NO-ONE answers the phone. I have sent emails, but all I get is an automated response telling me to go to the web site. Partselect is the worst company I have ever dealt with, I need to return about $100 in parts and I cannot get an automated return form or someone on the phone. I will NEVER do business with ... Read more them or recommend them to anyone. In a nutshell they SUCK as a company.

The instructions given on this website were more than adequate, even though the element had been updated and now has only 1 point to screw down

ordered new broiler pan

screwed it in the oven and it worked.

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Pop old one out and new one in

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. ... Read more Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

I purchased an 8" canning element for my new Kenmore Stove. The ordering process was easy. I printed my order out. I did not receive a confirmation by email, however I received the part in a timely manner. I was satisfied with the process.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you