Models > JES1288SH03 > Instructions

JES1288SH03 General Electric Microwave - Instructions

All Instructions for the JES1288SH03
16 - 30 of 38
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Power cut off to Microwave - It was run empty
1. Remove trim kit - Philips head screw driver
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
Parts Used:
THERMOSTAT MAGNETRON
  • Michael from POTOMAC, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door switch broke
Went on line and saw the Video - very simple to follow - very easy to remove and install the new switch -- went like a breeze!
Parts Used:
Light Bulb and Socket
  • J Theodore from RESTON, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave was popping and sparking flying
Removed the old wave guide cover and replaced it by slightly bending the wave guide cover and inserting 2 tabs on each side into the slots on the side of the micro/convection oven. I was ready to purchase a new appliance. Googled the model number, looked at a couple of sites and read the problems others had with this appliance and found my problem. I saved $$$ by purchasing the part and extended the life of my 11 year old appliance.
Parts Used:
Wave Guide Cover
  • Donna from RANGER, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unable to push fastening button into wave guide cover without cutting or tearing
pushed guide cover into place without fastening to button
Parts Used:
Wave Guide Cover
  • Dale from BEREA, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
missing parts
they had everything I needed, friendly service, fast shipping, no problems
Parts Used:
TRAY Circular Metal Tray - Black GUIDE ROLLER Assembly
  • John P. from Tucson, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door glass cracked
Remove the door and order the part. With in a day the part was at my front door. 30 minutes later was using applicance. Superb service from this company!!!!!!!!!
Parts Used:
DOOR Assembly
  • Bertha from MIddle Port, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior Light Bulb Failed
Light bulb repair was super easy once I got the out shell of the microwave off. The unanticipated problem was that I didn't realize the outer shell was secured with unusual "Security Torx" screws I have a couple star screw drivers but these were very unusual and could not find a proper screwdriver to remove them. I was able to force them lose with a small philips screwdriver and a pair of channel lock pliers. It took me quite a while to get the screws off this way but once I got them out and the outer shell off the microwave the light bulb replacement took less than 10 minutes. You should market the appropriate screwdriver to remove the outer microwave shell with any interior replacement parts.
Parts Used:
Light Bulb and Socket
  • Ricky from Lafayette, LA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave stopped working
Our microwave oven stopped working one day when the door was closed. The clock stopped showing, the light didn't come on when the door was opened, and the microwave couldn't be started. It acted as if it lost power. So, we did the usual things such as check the plug and the circuit; these were fine. I then removed the cover (need special bits called "Security Bits" which you can buy from Home Depot for $8.00). After removing the cover, be sure to discharge the capacitor (do a Google search to learn how to do this; fortunately, this microwave has a resistive circuit to ground to discharge the capacitor after about 30 minutes of being unplugged). After I discharged the capacitor, I checked the fuse and it was blown. So, I went to the store to buy a new fuse. When I replaced the fuse, and plugged the unit back into an outlet, the circuit blew as soon as I opened the door. This made me realize the faulty components were the "interlock" switches. These are relays (an electric switch) that cause the microwave to shut off when the door is opened and the inside lamp to illuminate when the door is opened. There are two "primary" switches and a "monitor" switch. I checked both primary switches for continuity (do a google switch for "checking interlock switch"). The one interlock switch was bad, meaning, it wasn't opening when it was suppose to. I ordered a replacement and also replaced the Monitor switch too (not sure why, I guess because it was only $6 to buy). After replacing the bad primary interlock switch, I put it all back together and we're working now!
Parts Used:
SWITCH MON. Primary/Secondary Switch
  • Timothy from College Station, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
tray would slowly rotate when door was open.
I determined that one of the 4 micro switches that interface with the door was faulty. Ordered that part and replaced it. Had to remove the cover and front control panel (without removing any connections. Two philips screws hold the limit switch assembly to the bracket. After removing those screws, twist the whole switch assembly clockwise around the mounting frame and now you can remove the defective micro switch and replace it with a new one. This works for any of the 4 switches.
Parts Used:
Micro Switch
  • Bruce from Hanover Park, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
opened door , oven shut off instantly
First remove tamper proof screws with vise - grips. Unplug capacitor ground out one side to discharge. Trouble shooting guide in a envelope in microwave, read it and did what it said. If 20 amp fuse is blown ( which it was ) replace primary and secondary switch and monitor switch. Switch assemble removes as a unit. Wires where hard to remove, you have to push on a release located on one side and pull to remove. Works great , only one switch was bad, but I did what the guide said. Draw a picture of wiring with color code so you do not mix up.
Parts Used:
Micro Switch SWITCH MON. Primary/Secondary Switch
  • Andy from Satellite Beach, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Did not have proper tool
Understand the type of fasteners GE used in the appliance require a BRISTOL type screwdrive.....unfortunatley this tool is not a part of my tool chest.....after running my four letter vocabulary and the use of thin blade screwdrive a a small vise grip plier was able to get the little bugers out.....thank goodness there was only four.
Parts Used:
Light Bulb and Socket
  • Charlie from Avon, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Replaced magnetron and spreader plate
on the kitchen counter. Removed parts and replaced exactly as the came off. insuring all fits were tight and secure.
Parts Used:
Wave Guide Cover
  • Joseph from Mobile, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burned out bulb
It took two people because we have built-in unit. The power plug was in cabinet above.First had to remove front frame in cabinet with Phillips screwdriver. Removed microwave from cabinet box (be sure to wear gloves, edges are very sharp). Then unscrew outer shell of microwave - easy process. Easy task to remove bulb/socket piece. We ordered part from Part Select - friendly service and the price is the best. Even with minimal shipping costs, the local prices were more than double. Important, it is a bulb and socket part.
Parts Used:
Light Bulb and Socket
  • Veronika from St George, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Microwave is completely off!!
My husband burned the microwave by using alumifoil. It was working for a little while after that but next day, the microwave was completely off. He thought the thermostat was broken, ordered the part and replace it. It's fixed and working fine now. Someone mentioned that if you put the broken thermostat in the freezer, it will be reset and fixed. I tried that also. I wrap the thermostat and put it in the freezer for one day. Now it's working!! I didn't know about that before I ordered the part but it wasn't expensive at all. So now, we have extra thermostat!!
Parts Used:
Thermostat Cavity
  • Takayo from Moody, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lite bulb
First you have to get the "security screws" out with a pliers or vise grips then it was a snap, just replace the screws with 1/4 drive screws for the next time you have to get in there !
Parts Used:
Light Bulb and Socket
  • vincent from McCaysville, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JES1288SH03
16 - 30 of 38