Models > JED8430BDS > Instructions

JED8430BDS Jenn-Air Cooktop - Instructions

All Instructions for the JED8430BDS
31 - 45 of 60
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Knob on the exhaust fan was broken
Simply removed old knob and replaced.
Parts Used:
Fan Knob
  • James from Sacramento, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
sticking/broken pop up knob
I used needle nose pliers to remove the broken piece then pushed the new knob on!!
Parts Used:
Fan Knob
  • Robert from Northville, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace old grease filter
very easy slip in
Parts Used:
Cooktop Downdraft Vent Grease Filter
  • Rita from Leesburg, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan not working
Opened the top section of the stove. Re-routed wires to be connected from the speed control device into the new cord. And done. Put everything back thogether.
Parts Used:
DISCONTINUED
  • Roberto from Zapata, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench set
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Aged parts
Parts aged from wear
Parts Used:
Top Front Trim - Stainless Burner Knob Cooktop Rear Trim - Stainless
  • Kathleen from Pottsville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
I didn't end up with the correct item
I ordered a switch and got a switch knob. So it is still not working.
Parts Used:
Fan Knob
  • Gary from Dana Point, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
Was this instruction helpful to you?
Thank you for voting!
Surface Burner Short
Removed the cook top from the counter. Removed the switch housing and then the switch. Found a match and ordered. Part came in 2 business days. Once I put together the housing and connected the wire housing the burner worked perfect. The downdraft fan remained on. Placed a call to Jenn Air service and was asked to disconnect the fan switch. There must be some memory in the solid state portion of the switch. After a few mins I replaced the fan switch and hooked up the wiring. All worked fine.
Parts Used:
Surface Burner Switch
  • John from San Antonio, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
replacement of broken knobs
open packaging and placed knobs on stems of the cooktop.
Parts Used:
Burner Knob
  • Yulanda from Fairburn, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Fan swith poped out -couldn't replace it
Ordered new part--on line help said pull all remaining parts out--small pair of plyers and yanked internal parts out--the new part just slipped down over the u-post and back in business--couldn't have been easier
Parts Used:
Fan Knob
  • Raymond from Long Beach, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Water boiled over burnt out switch
Knocked breaker removed stove top from iland removed a dozen screws replaced switch put screws back in installed top back in iland put breaker back in worked purfect.
Parts Used:
Surface Burner Switch
  • Eddie from Loyall, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Fan knob would not pop up as designed.
Removed old knob by pulling straight up. The shaft the knob fits on is D shaped. Simple align knob with D on shaft and push down. Problem solved.
Parts Used:
Fan Knob
  • Raymond from Soddy Daisy, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
burner switch broken
turned off power to stove top..lifted unit out unscrewed top and switch had 2 screws re-placed switch and put back together.. make easy $100 plus switch
Parts Used:
Surface Burner Switch
  • larry from houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Our old grease filter was molding
Took the old filter out and put a new one in. No tools no fuss no muss. Very easy.
Parts Used:
Cooktop Downdraft Vent Grease Filter
  • Kathy from Gurnee, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lost one turner knob and others were a mess. Center airgrille was getting old and discolored
Just slipped the perfect parts in.
Parts Used:
Burner Knob Air Grille
  • Elizabeth from Hudson, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replace broken fan knob
Only had to get long-nosed pliers to pull remains of broken knob from cavity. New knob was easy push-on and repair was completed!
Parts Used:
Fan Knob
  • Allen from Winchester, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JED8430BDS
31 - 45 of 60
Back to Top