JED8345ADW Jenn-Air Cooktop - Instructions

I got the switch wired correctly, with much cussing. It worked - burner heated. But I couldn't get the new switch to fit back with the old ones neatly enough to close the box and secure it. Got help from someone with stronger hands but still couldn't get it to fit. On top of that I found that the new knobs didn't fit on the new switch - or even on the old switches. The old knob didn't fit on the new switch either. I gave up. Removed the new switch and took out the corresponding burner. Still have 3 burners that work.
Repair folks had warned me that I couldn't get parts. They didn't say that it would look like there was a replacement part but it wouldn't fit!

I disassembled the stove top and replaced the components.

I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on

We removed all the screws in order to remove the top cooktop frame. Once we did, the bottom part of the cooktop fell! It was being held up by the vent that goes underneath. My son and I had to get underneath to push up while my husband tried to position the cooktop back over the counter top ledge. It was VERY heavy. This was difficult and needless to say, it fell a couple more times before we finally were able to keep it on the ledge. We had to turn off the electricity, pulled the element out and disconnected the two wires, installed the new light and then placed the cooktop cover back in place by screwing all the screws. We did test the light before screwing on the cooktop cover JUST in case...:) It worked!

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Turned off power to range top. Two screws to lift the control area. One snap on was burned off.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.

removed two screws under fan cover at end of stove knobs. raised panel with knobs up and removed two nuts that held fan switch housing. installed new switch and moved power connections to new fan. (note: Killed power to range top prior to any repair action)

The switch did not fit in and had to be returned.

switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.

Pulled the old one out & inserted the new one. Less than five minutes.

We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!

I just lifted out old filter, and put in new one.

Removed old filter, dropped in the new one.
(This really was not a "repair")