JE2160WF03 General Electric Microwave - Instructions

We removed the glass circular plate of the microwave. We replaced the original roller guide with the new part. Then we placed the glass plate back in its place. Quick and simple.

This was an under counter microwave located above the range. There is a cover on the bottom of the unit that contains screens for the fan. This cover is removed by taking out 3 screws located near the front of the unit. Be sure to support the cover when removing the last screw. There is a plug-in wire going to the turn table motor. Unplug it so you can lay the cover on the range top. The motor is removed by taking out two screws and pulling down. It should not take much force as it slides into a plastic drive located under the turn table inside the microwave. There should be specifications on the old motor that match the new motor. Push the new motor up into the plastic drive unit, matching the "D" shaft of the motor into the plastic drive. Replace two motor screw in correct holes so that the plastic drive is centered in the hole. Plug the motor back in and replace the cover.

The key to this repair is attaching the spring once the rest of the assembly is attached. I primarily used a wratcheting screw drive to remove the assembly but used a socket attachment with the screw bit to finish it off.

First, I removed the spring entirely. In order to attach the spring, I expanded the spring by sliding quarters into each of the coils (I had a quarter in every coil in order to get the ends as close as possible). I then first attached the spring to the post on the right side. I would have preferred to attach it to the closure assembly arm as the angle to attach was much simpler with the spring detached however there wasnt enough room to work around the post.

I then adjusted the closure assembly arm to be aligned with the spring and with a little elbow grease, stretched the string the remaining 1/2" or so and connected it to the arm. Once connected, I opened the fridge door and was easily able to remove the quarters.

Removed the unit from counter, opened metal housing, removed Humid sensor from top left side of unit, unpluged wire from curcuit board. Installed new Humid senor, metal housing and reinstalled unit into counter top. Microwave works like new.

Thanks
John

Fast & easy. I was able to determine that this foot would work from the descriptions on online!! Thanks

1. Remove trim kit - Philips head screw driver
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit

Went on line and saw the Video - very simple to follow - very easy to remove and install the new switch -- went like a breeze!

Removed old roller assembly and installed new roller assembly.

I placed the new hot plate in the old microwave. It worked perfectly, and no tools needed

Take the four saftey torx screws off the back of microwave that hold the side panels on. There are no screws in the front. Just pick up the side panels a little and slide towards the back of microwave and it will come off. The magnetron is visible behind control panel. Unplug the magetron, take a 3/8 nut driver , remove the one bolt that holds it on , remove and replace with the new one. Plug the wire (it will only go one way) back up and replace cover.

Went well, very easy to change once the microwave was out of the wall. Sounds better than when it was new.

Replacing the light bulb is easy and takes no more than 15-30 minutes. The light bulb is located behind the grill on the right hand side of the microwave as you face the microwave. To get to the bulb you have to remove the outside cover. On mine there were three screws that had a special head and required a special tool. That was a surprise! To work around that, since I did not have the tool, I used a pair of needle nose pliers to grip and turn the screw head. They came out easily. I replaced them with the same size Phillips head sheet metal screw when I put the cover back on.
1. Remove the screws that secure outside cover and take the cover off.
2. Locate the light bulb and unplug the power wire. It is a two prong plug that pulls off with little effort.
3. Remove the old light bulb. It is held in place by a plastic tab. Push the tab toward the outside of the base plate with a small screw drive or your finger and lift the base plate. The bulb will come out with the base.
4. Install the new bulb. Align the holes in the base of the new bulb with the tabs on the socket and put the bulb in place, ensuring the tab secures the bulb base in place.
5. Reconnect the power wire to the bulb.
6. Reinstall the outside cover.
7. The light should come on when you open the microwave door.

Remove the Glass rotating tray and replace the guide

Light bulb repair was super easy once I got the out shell of the microwave off. The unanticipated problem was that I didn't realize the outer shell was secured with unusual "Security Torx" screws I have a couple star screw drivers but these were very unusual and could not find a proper screwdriver to remove them. I was able to force them lose with a small philips screwdriver and a pair of channel lock pliers. It took me quite a while to get the screws off this way but once I got them out and the outer shell off the microwave the light bulb replacement took less than 10 minutes. You should market the appropriate screwdriver to remove the outer microwave shell with any interior replacement parts.

Our microwave oven stopped working one day when the door was closed. The clock stopped showing, the light didn't come on when the door was opened, and the microwave couldn't be started. It acted as if it lost power. So, we did the usual things such as check the plug and the circuit; these were fine. I then removed the cover (need special bits called "Security Bits" which you can buy from Home Depot for $8.00). After removing the cover, be sure to discharge the capacitor (do a Google search to learn how to do this; fortunately, this microwave has a resistive circuit to ground to discharge the capacitor after about 30 minutes of being unplugged). After I discharged the capacitor, I checked the fuse and it was blown. So, I went to the store to buy a new fuse. When I replaced the fuse, and plugged the unit back into an outlet, the circuit blew as soon as I opened the door. This made me realize the faulty components were the "interlock" switches. These are relays (an electric switch) that cause the microwave to shut off when the door is opened and the inside lamp to illuminate when the door is opened. There are two "primary" switches and a "monitor" switch. I checked both primary switches for continuity (do a google switch for "checking interlock switch"). The one interlock switch was bad, meaning, it wasn't opening when it was suppose to. I ordered a replacement and also replaced the Monitor switch too (not sure why, I guess because it was only $6 to buy). After replacing the bad primary interlock switch, I put it all back together and we're working now!