JDS9860AAW Jenn-Air Range - Instructions

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.

Took the old levelling leg out and screw the new one in.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Very easy repair. Turn the power off to the oven, take out two screws and unhook electrical connections. Replace with the new baking element and you are done. Takes only about 10 minutes and the oven works like new.

Replace filter

Opened the range grid, popped in the new filter, seconds after that I pulled out the old door gasket, put in the new with its little poppers and that's it. Both jobs took me less that 3,minutes. Great.Easy install for both products.

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!

Put a new one in.

I haven't done anything yet because the part I am replacing is different from the one i have to order. I guess you might say I am getting screwed. I purchased the grill burner for $234.00 plus tax and shipping. Then realized I needed to purchase an igniter. My original one came with 2 igniters attached to the burner part. These new ones are all separate. $55 and $49 if i remember correctly. I ordered just the larger one and I am hoping I do not have to buy the smaller one. The large igniter will not even arrive until the end of August that is 6 weeks after the order date. I was told by the customer service rep it would only take 10 days to get it to the warehouse.The price tag is over $500 just to replace the grill burner on my stove top.That is some rip off. Otherwise my stove top is in excellent condition.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!