JDB8200AWP0 Jenn-Air Dishwasher - Instructions

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

Upper tray removed and each rack adjuster removed and replaced one after the other. Only tool was screwdriver. Only knowledge was from the online videos. Only took 30 minutes or so. The repair could have been done more quickly if I wasn't fearful that the smaller plastic parts would break when pulled or pried away from the rack adjuster. The only mistake was not making sure the adjuster tabs were fully engaged in back and clicked in the front attachment.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Pulled out dishwasher, removed 4 bolts holding the track to the dishwasher, replaced track and installed the 4 bolts. Pushed back the dishwasher and works like new. The new tracks are riveted instead of spot weld and will last longer.

This was so simple! Some plastic tabs snapped off the upper rack adjuster in our dishwasher (which is not even 4 years old, so you can see how crappily made these things are), rendering the entire appliance unusable since the water sprayer thingie attaches to the underside of the upper rack. I was able to easily find replacement rack adjusters on PartSelect and thanks to the repair video, was able to install them in about 20 minutes. Most of that was rewinding the video since I had trouble getting the broken adjusters off! So delighted to have been able to do this myself and avoid paying $$$ for a repairman call out and replacement parts.

pulled the dishwasher out (took the most time-1 hour) and 30 min. to install new door balance kit and springs. Replace both sides while the unit was out.

leveled dishwasher, it was leaning forward, raised front 1/2'", to get level.
no More leaks, WOULD LIKE TO RETURN DOOR SEAL. DID NOT USE SEAL.

THANKS,
PETE GODSHALK

I needed to replace the black access panel on my Whirlpool dishwasher (model WDF520PADM7).

By following the instructions in this short video (https://www.youtube.com/watch?v=995mtdO7rQg) , I was able to complete the replacement in under 10 minutes. You'll need a flat-blade screwdriver. The Retainer Clip - Black can be a little tricky to position into the opening, so have patience.

Keep in mind that the Retainer Clip - Black only contains ONE clip and so you must make sure to order TWO Retainer Clip - Black from PartSelect.

I ordered the part from this website and easily replaced it.

Removed the upper rack and replaced both side with new upper rack adjusters that are now metal and not plastic!

Ordered the door gasket and replaced it. Worked perfect. The trick was to stretch the gasket a little as it went around the top curvatures. It would stick out some and not sit as flat as on the top and sides. This helped it to flatten down better.

These wheel assembly that came on the lower rack of my dishwasher were junk! They started falling off within 6 months. I put them back on to the point that the pin in the center of the wheels would no long stay in place, thus the frustrating situation of the wheels falling off often.

Assembly was easy peasy!

My husband did the repair. It was very easy. He basically just popped off the old wheels and popped on the new ones.

The 1st person i had contact with wasn't any help choosing the correct part. Paid about $30.00 for the wrong part. Paid $8.00 more to ship the wrong part back for reimbursement. Meanwhile my son went to a local repair shop and got the right part for less than $40 and the repair shop installed the part on the rack for free
I was not happy with Part Select! Part Select cost me time and money and didnt get the job done

Per suggestions from other reviews, I looked for You Tube videos for replacing this part. The video I used was completely necessary, but moved way too fast, so required lots of stopping, rewinding and starting again. But I managed to get the old rack adjuster removed and the new one installed without too much trouble.
Then I tried installing it in the pull-out rail. The front connector on the new adjuster would not fit into the appropriate slot. Initially I thought maybe the part was defective, but determined that the dimensions were as accurate as my eye and tape measure could evaluate. Finally, I settled on the expedient of filing away at least 1/16" from one edge of the slot so that the connector would drop into place.
Not sure why this discrepancy existed but the problem appears to be resolved.