JDB7910AWW Jenn-Air Dishwasher - Instructions

follow the instruction on the web site that you listed.

1) Emptied Dishwasher (roll-around model)
2) Tipped it onto its back
3) Removed Toe Kick (2 screws) and Bottom Cover (4 screws) (screw driver)
4) Opened Door to access side panel (careful not to let it drop on my fingers)
5) Using Torx driver, removed two screws holding side panel on. This makes it easier to access the linkage and spring.
6) Removed broken link
7) Installed new link and spring noting the spring direction from the spring on the other side of the door.
8) Pulled spring over the bottom rail bracket with pliers.
9) Reinstalled panels in the reverse order.

This was really easy. I just took out the two screws securing the unit to the counter top and slid it out about 6 inches. Broken plastic spring linkage was obvious and easily accessible. I didn't know there was one on each side, I would probably have went ahead and ordered both and replaced them at the same time.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

I pulled out the old rack, removed the spraying apparatus, attached it to the new rack and slid it into place.

My handy husband was able to take it apart easy, and then your online site was great at showing us exactly which parts were needed to replace. Then a few mintues to put the 4 pieces together and now I've got all the room I need for the extra dishes!!The whole experience was so easy and very helpful!! thank-you very much!!

I simply connected the two hoses to the valve plugged in the two wires and it was working!

I first removed the bottom access panel and 2 upper screws holding the dishwasher to the counter. Be sure to remove the standing water in the bottom tray. I pulled the chassis far enough forward to reach where the top shower hose attaches ( the supply line and wire had enough slack to move the chassis ). Not knowing how the rotating shower arm attached, I unscrewed the ribbed retaining ring above it, and found the whole assembly came loose - freeing the upper end of the shower hose. Put a shallow tray under the lower end of the shower hose to catch the remaining water and loosen the hose clamp to free the remaining end of the hose. Transfer the rubber washer at the top end and the hose clamp at the bottom, to the new hose and install. A quick repair, but one that shouldn't be needed on a 4 year old dishwasher.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

I first removed both lower front shields,(4 screws)
I then shut off water supply to inlet valve from hot water supply. I removed the water hose from inlet valve,two electrical terminals,( I put tape on right side terminal and lettered with an R as not to mix up the two terminals)removed the hose clamp,removed valve from frame.I reinstalled in reverse procedure.I turned the water back on and checked for leaks.I started the normal cycle and water flowed into the dishwasher as designed.

The rack assembly was not altogether assembled. Had to remove one part from the old one and reassemble on the new. Also, The racks that make place for a bowl instead of plates was not assembled.

Attaching the part to the door only took a few minutes but getting the dishwasher out over the hardwood floor that was installed after the appliance was put in was a pain. I had to remove a piece of the hardwood floor and use some technique to get it out of the opening so that the springs were visable. There is no problem after that. I would recommend using work gloves to stretch the spring over the retaining notch on the door so that you don't pinch your hand.

purchased disk rack was complete exept for the water diffuser in the middle of the rack. Merely pulled to old rack out with no tools, twisted out the diffuser and tweisted in to the new rack.

No tools or instructions required.

Initially I suspected something had found its way to the impeller or the macerator, began to disassemble top down. Upon removal of the discharge it was apparent the plastic disc at the top of the discharge was sheared off. Located the schematic at PartSelect and ordered the discharge. Received part within 3 business days and installed new discharge in about 30 minutes. Required 5/16 socket and hex head driver. Recommend ordering new gasket with part.