JDB3650AWR4 Jenn-Air Dishwasher - Instructions

I removed inner face of door, cut wires leading to door switches, and then installed the new door switches and wire harness.

Removed old parts by breaking them with a screwdriver. Insert thr stainless slide. As shown by twisting thought through wire rack the rest is easy.

Disconnected dishwasher from countertop and slid out about 1.5 feet.
Removed old link.
Installed new link and reconnected to spring.
slid dishwasher back under counter.
Replaced 2 screws back to countertop.
It was really really easy.

The left side took 20 minutes the right side took 3 minutes. The instructions do not describe how to remove the old assembly but rather just assume you have already done it. It takes one minute to see how the six parts fit together and then you just have to begin disassembling the easiest piece. The final cover removal required a flat head to pry apart two pieces held together in a pressure fit with round tabs locking them in. I was worried about breaking a piece in case the new parts didn't fit properly and I would have to reinstall the old pieces temporarily but you just have to keep the faith and open it up for final removal. Installing the new parts was simple however it would be nice if the images on the instructions were of better quality. The result was perfect and the kit feels more robust than the original parts. There is nothing here an average person can't do with a screwdriver and a little patience.

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

I found an exact match to my rinse aid cap on your website and ordered it. It came to my house in 2 days. It fit the dishwasher, and I used it tonight for the first time with the rinse aid. (With the change in detergents, the detergent alone was not leaving the dishes and silverware feeling smooth and clean.) The dishes came out much better tonight.

I ordered this part after the sanitized light on my dishwasher was flashing. The dishes were no longer drying. To replace the part, my husband pulled out the dishwasher and unscrewed some nuts (accessing under the heater through the side openings). The entire repair took under 15 minutes, and works perfectly. I have to mention that the heater was shaped differently than the one it replaced, but was a perfect fit in the clips.

Turned off water supply and electricity, removed the front kick panel on the dishwasher. Disconnected the water supply line, removed the two screws above the door securing the dishwasher to the underside of the countertop. Pulled the dishwasher out from under the counter, replaced the spring and balance link for each side. I found that the new balance link kit that I purchased was better engineered that the origanal equipment.

Remove two screws at top that fasten dishwasher to cabinet. Slide dishwasher out to expose the two links that attach the door to the springs. Fit the new links to the springs and door.

Removed old seal, cleaned track, applied adhesive for new seal, seated new seal in track, closed door for 24 hours to allow adhesive to cure, then used dishwasher without difficulty. An easy repair.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

This kit comes with the link cords and the balance wheels. I only needed the cords. I undid the set screws under the counter edge and slid the Dishwasher out from under the counter. One of the links had a broken cord and the spring had snapped to the very back of the space and was a bit hard to find. I used the good side as a guide to see how to thread the cord correctly. I did not replace the wheels since they appeared to be in good shape and looked like they might be a bit more difficult to replace than just the cord. For a second I thought I had ordered the wrong part because the new cord's attachment point at the hinge did not look exactly like the originals but the new design worked just like the original. I did need one other person to help stretch the spring and hold the door in the best position so I could attach the cord to the hinge. It's working perfectly now and I saved the wheels in case I need them later.

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

First, ordering parts and getting diagrams from parts select is so efficient and make tthe installation so manageable. Using installation tips off the site gives u confidence to do it.
My issue was that I could not get the dishwasher from under the counter.
I removed the kick plate and screws holding it to the counter, but it was not coming out all the way. So I had to use a coat hanger to hook the spring. I attached the nylon cord first. Then I pulled the spring taut with the hanger and it was easy to thread the cord around the pulley system. I actually attached it to the door before tensioning the spring to make it easier.
Door works great now.