JDB1250AWQ10 Jenn-Air Dishwasher - Instructions

I removed the old rack adjuster by unscrewing four screws. I put the new rack adjuster in place, carefully fitted the adjustment parts together, then replaced the four screws. The best part of the repair was that Parts Select had originally indicated that my part would be on back order for a few weeks, but I actually received the part within just a few days. What a nice surprise - thanks!

I snapped off the 2 old parts, ordered the new ones and snapped them back in, however, the new parts are not the same as the old ones and do not do the job of holding the collapsable tine rows up...now they just fall over. Guess I have to call Jenn Air.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

Snapped out the old retainer, snapped in the new. Then snapped in the washer arm. Done. Works great.

Took the dishwaher apart. Found out the float was damaged. Replaced the float and the float switch. Put back together

Basically took out of box and put in dishwasher.

I unscrewed the old rack adjuster assembly and screwed the new one on (this was after I took the rack out of the diswasher) -- I actually saved one of the old intact plastic wheels for future repairs.

After noticing that the nozzles in the washer arms seemed clogged, I ordered replacements from PartSelect.com. Installing them was a breeze. The upper arm had a torx screw in it and the bottom just required a nut driver to get off. I replaced the arms and ran some DishWasher Magic through it and now my dishes are clean again!

Removed the bottom tray. Removed the two clips in the top tray guides and removed the top tray. Removed the top spray arm and transfer tube by unclipping it from the top and at the back and then rotated it down and out. Removed the six screws around the upper pump housing and removed it along with the bottom spray arm. Removed the three screws holding the filter protector plate and removed it. Removed the two screws holding the accumulator / flow plate and removed it. Put it back together in reverse order careful to not over tighten the screws.

Removed the bottom cover.with a flashlight and a mirror found the problem. Went to Maytag they told me that in 8 warehouses there were no parts. They did give me a enlarged view of the part that I needed. went on the computer to PartSelect called PartSelect talked to a very helpfull Lady ordered my parts. Job is done Mama's happy Lifeis good. Thank You

I noticed that the dishes on the top rack were not getting clean. While the dishwasher was running, I opened the door to see if the arms were moving/spraying and they were not. I cleaned the filter and checked the impeller and both were clean and not damaged. After looking how the top rack slides into the "flapper" I took it off to inspect it. It was missing the rubber to make the seal with the tube from the top rack. After replacing this part, the dishwasher is cleaning like new. Here is the part PS2340934 Docking Station with Flappers

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

By reading online about some similar problems, I discovered that the accumulator did, in fact, have some holes worn through the screen and was leaking sediment back into the rinse water. After waiting for 2-3 months because the apart was on back-order at the factory, it took me less that 1 hour to remember how the unit went together (reviewed the parts diagram online) and connect everything up. On the first rinse, the dishes were really clean - well worth the wait. Doing dished by hand reminded me of the old days....

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.