JCB2581WES00 Jenn-Air Refrigerator - Instructions

first i put in a new water inlet valve it did not solve the problem i waited 3 days then ordered the ice maker i put it in an it still did not work after 3 days i put in water in the ice maker by hand it still did not work i gave up then to my surprise 4 more days it started working still not sure what was wrong but i am glad it works now this was about a two week process one tip on getting ice maker out is to take the door that's covers ice maker off no tools needed then remove three screws slip it in an out there is a helpful video for water inlet thank you mike b

After deciding it was the unit itself and not a water celenoid I ordered it from parts select. Instead of 3 to 5 business days it arived the next day after ordering. I had previously removed and reinstalled the ice maker while trouble shooting. It was easy to change it out, and works perfectly.

After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.

I unplugged the refrigerator
Opened the freezer door
Opened the ice maker door so that I could easily get to the emitter and receiver
I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate
I unplugged the faulty circuit boards--this took some tugging
I firmly plugged in the new circuit boards and replaced the screws
I waited about 30 minutes and the ice maker began making ice again

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.

plastic warped in ,spaced out and, the socket snapped back in place.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Removed one screw, carefully removed the unit, unplugged it and reversed the process to install. My only issue was the picture of the part I ordered was not the same as I received.

Repairing a refrigerator is inimidating to say the least. Our ice maker has broke twice in the two years that we have owned it. The first time we had a service repair faciliting come out and they replaced it for about $200. The second time I had no idea what the problem was until I came to this repair forum. I soon realized that the electronic control boards needed to be replaced. Received the part two days after ordering and it took all of about 5 minutes to unscrew the old boards, pop them out, and put in the new ones.

Love your website and the money that you saved me!!! Thanks a million!

Light was blinking on the Electronic Control Boards. Ordered replacement (emitter and receiver)and installed, and now it's working.
Some note: 1 year ago, the board started to blinks (meaning it's bad) but it was still making ice. This gave me a false error when it really failed, took the risk and ordered the replacement parts and all is well now.

One more thing to pay attention to , and it may only be on my model of refrigerator, but the wires harness that connect to the receiver board (big board) have large and stiff wire. With limited space where the board and the wire are seat at, it put lots of pressure on the pressure on the board's connector. This pressure, over time, will cause the right angle connector's solders to crack and may be a contributor to the failure. If you're installing the new board, try to re-inforce the connector with some rubber heat glue and also relieve pressure from the connector's end, which I hope will prolong your board.

I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk

power off, 3 phillips head screws on either side of freezer. unplg each board, plug new ones in completely. ( cannot mix them up, size difference) replace screws and enjoy ice cold beverages once again!!!!!!!!!

Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.

Not being a professional repair tech, I looked at this sites provided schematics of the ice-maker. I assumed due to the problem I had which parts to order. the parts arrived within 3 days and after I took the icemaker apart I quickly realized I ordered the wrong parts. I called and asked what to do. since I did not open the packaging for the "wrong" parts I was able to make a return. I then called back because I discoverd the part I really needed wasn't shown in the sketch. I was told that I needed to order a new motor and it would have the part I needed. I ordered the part and within 3 days it arrived. Once I had the new part I was able to quickly install. Now I have a icemaker that works better than new since ,now it does not seem to jam either.

To make the repair:
First remove the 1/4" nut head screw on the under side of the ice maker.
Remove the shroud covering the electrical connection.
Slide out the maker and depress the locking clip.
Disconect the electrical wires.
Pull off the motor cover (no screws).
Remove the three philips head screws from the motor housing. Gently remove the motor.
Next loosen the screws and pull the "black motor-mounting harness" untill enough clearance to remove the ejector arm and deflector tray. The new kit will have a new ejector arm and deflector tray.
Insallation is the reverse.
The schematics were very helpfull.
It was very simple and I saved a $150 service fee to have someone else do it for me.
PS. When I called I was able to speak to real live Americans who were able to help me, were pleasant, polite, and professional, AND they did not treat me like I was stupid because I am not a professional repair man. I will definately use this service again. and recommend to all my DIY friends!!

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed