JBS55DM2WW General Electric Range - Instructions

Followed the directions!

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Removed door from range(see manual for instructions). Set door face down on protective cloth material .Remove two top screwws, 3 bottom screws and lift back of door off. Remove two screws on each side of door bottom channel and remove channel. Put in new trim on bottom of glass window and put screws back in. Set back of door on top of front cover and screw two top screws and 3 bottom screws back in. Set door back into range. Lock clips on both hinges.

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!

Baking element : Pull range away from wall. Disconnect the power. Remove back center panel. Remove range door. Remove range racks. Disconnect push on terminals fron baking element. Remove two hex head screws. Remove baking element. Reassemble in reverse order..........Temperature sensor: with back panel removed, unclip the electrical connector. Remove one hex head screw. Remove temperature sensor. Install in reverse order.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

The part was exactly what we needed. However, we didn't find the video online to show how to replace the part until we were almost finished. (https://www.youtube.com/watch?v=ovwcJhfWHXQ) If we had found the video, it would have saved us a lot of time because we undid more of the door than we needed to. Also, the video tells you exactly what size tools to use. However, taking the door more apart allowed us to clean more of the inside of the door. So, watch the video before you start, and also, be prepared to spend time cleaning the insides of the door. Also, when we put the door back together, we accidentally turned the front glass panel of the door upside down and it wasn't noticeable until we had put the door back on the oven. So, we had to take it apart again to fix it. All said, we're very happy with the new part. Thank you PartSelect!

First I removed the screws and popped off the existing element. One of the wires "disappeared" back into the insulation, so I had to remove the back panel of the oven to access that wire and push it back through the opening. Then I attached the new element to the wires and replaced the finishing screws.

We ordered the part, it arrived quickly my husband removed the burnt out element. We took the back off the stove in order to install the new part. It was easier to connect from the back than reach in to the oven. An easy repair and the stove works fine now.

First I turned off breaker, pulled out oven unplugged/or dissconnected electricity to oven, unscrewed broken element in oven, unscrewed back panel of oven to disconnect 2 wires from element, and replaced with new element, then repeated the above in reverse.
Very easy for a typical DYI person.

popped out the remainder of old lens, then pushed in new ones and slipped on plugs.

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.

Unplugged Stove. Removed two screws. Unplugged two wires from heating element. Connected the two wires to new heating element. Replaced screws. That's all. 5 minute repair job.....(45 minutes to find right socket haha)

Ordered new heating element on Friday afternoon (3pm) and received part on Saturday at 1:00pm. Impressive! (standard shipping)