JBP45WW1 General Electric Range - Instructions

The burners were not level and would heat more on one side than the other. Since the range was 21 years old and would cost a lot to replace, I decided to replace the burners and
treat myself to new drip bowls. I Googled and got the information on the range including part numbers. I ordered them and am very happy. It was very easy to replace the old ones. Only problem the large drip bowl was dented but on sending an email to compamy, a new one is being sent. I am very happy at the ease since I am a retired widow of 76 years old. It pays some time to take care of the old and do a little reapair instead of spending a lot of money on relacement when every thing else is in excellent condition.
Thanks for making this a very easy experience.

I was very impressed how quickly the package arrived. I would you your company again. I found you with a google search.

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

part arrived very quickly. removed the rear cover. removed the old control unit. installed the new(retro fit) unit using the supplied wiring sheet diagram. The whole operation took about 30 minutes. Works great. Thanks PartSelect.

Removed the burner coil.
Unscrewed the terminal block.
Pulled out the stove and disconnected the 220 Volt service at the plug.
Removed the back panel at the control knobs.
Detached the wiring to the control knob and pulled thru the back panel.
Wiring mostly visable to the front 8 inch burner.
Replaced wiring and mounted new terminal block.
Tested the burner for a few seconds.
Replaced back panel and set stove in place.
Saved $150 dollar service call.

The initial symptom involved the heating elements turning off and on rapidly once high temperatures were reached. After cycling power to the range this went away for a few weeks. When the symptom reappeared, it involved the oven-on light turning on and off, even when the oven control was in the off position. This persisted after a power-cycle so I decided to replace the control board. The actual repair was quite easy. The hardest part was removing the sheet with the button labels from the old unit (I ended up inserting a knife and twisting it to separate the adhesive, which is only around the edges) and fixing it to the new unit in the proper position. The latter would have been much easier if I had realized up front that there are handy guide ridges against which to align it! Like another person whose repair story I read, the existing wire colors were not all an exact match. However each connector's function was clearly labeled on the PCB of the old board, so I had no trouble matching them up (line voltage was red, not black, and broil was blue, not purple). The only other difficulty I encountered was that the old yellow bake wire had a plastic guard on the connector and this did not fit in the appropriate hole on the new unit. I merely pried the guard off with a small screwdriver and used the bare spade-connector, which fit in the hole nicely. There was a small amount of exposed wire left, so i wrapped it in electrical tape although I doubt that was necessary.

This appeared to be an easy fix, but turned out to be more involved than I planned. The hard part was pulling the range/microwave oven assembly away from the wall so I could remove the back panel and see how the new terminal block wires connected up to the switch/knob that operates the burner. Extracting the whole range unit required me to use a floor jack to raise the leveling feet of the range above the edge of my floor tile so I could slide the unit out. Once away from the wall, I used a nut driver to remove the back panels. Next surprise was the new terminal block wire connectors were not the same type as the old block's connectors (flat vs. male pin-type). Rather than let the scope of this job creep to include a whole new connector rig, I opted to splice the new terminal block wires onto the existing wires that led up to the control knob. I used professional splices and a crimping tool to secure the wires. After checking the new installation was sound and operational, I slid the whole range back into place. Attaching the new terminal block to the range top was a piece of cake, but getting the damn oven out into open space where I could work on it was bear. But, hey, I learned a few things, one of which is that when a homeowner decides to retile their kitchen, make sure you run the new tiles all the way under the range and not just up to the front edge of the oven. I can see why this was done - to avoid having to remove the oven during the retiling - but it creates an obstacle for whenever the oven needs to be pulled away from its location. The last tool I imagined I would need for this repair was a car jack. The Parts Select part worked fine.

Replace part an wires

I removed the oven door by unlocking the hinges and pulling out. Set on workbench (with towel/pad) and removed handle, four screws, then bottom and inside panel screws, then one nut to finally be able to get at the inner glass insert. Removed insulation and then took an extra hour to really clean all surfaces (middle glass was quite greasy due to inner glass being broken for a while. Reassembly wasn't bad, but took a while to figure out that the two thin 2" red spacers belonged around the two handle screws. This was tough to figure out as they come off when taking the handle off, but you can't see them, so didn't know where they came from! Anyway, if you're just a bit handy, you can do this job.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

I removed the back to gain access to the control board. Then I unplugged each wire on the old control and plugged it in on the new control - one at a time. Then removed the old control, removed the face from the old control and put it on the new one. Next I installed the new control and replaced the back. Job completed - oven works great.

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.