JBP25GS2 General Electric Range - Instructions

Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

Removed 4 screws holding the control panel removed the receptacle wires removed the screw holding the receptacle in place. Inserted the new receptacle screwed it in inserted the the wires to control knob. Screwed the control panel in place. Replaced 2 burners and 2 elements with in a half hour. Simple. Received the parts with in a few days. Will order from here for now on. Before we ordered looked for parts everywhere could not find them. Thanks

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

This is far to simple to even be a worthy story ,other than that the cause is a bit interesting. My wife had placed a plastic cutting board and some meat into the oven to get it away from my counter-cruising dog.
Later, without remembering the cutting board she turned the oven on to "broil." Hmmmm...

REPAIR:
Open oven door
Put in new rack
Close door

I looked on Youtube for a how to video. It was accurate but the screws in my oven were NOT phillips head screws, they turned out to be sheet metal screws. I used pliers at first which was a PAIN but then I borrowed a socket wrench from the neighbor that was MUCH better!! I had wanted to do it myself to prove to my husband and son that I could but I ended up needing their help because the screws were so tight.... But we did the repair ourselves!!!

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!

Unplugged the range, took old elements out, put new ones in. Couldn't have been easier and for the total cost of about $60; I have a working oven again. A LOT cheaper than a new $600 range!!