JB670SP2SS General Electric Range - Instructions

Pulled the oven out of it's location. Disconnected the power cord from the Electrical Outlet. Removed the Protective back plate (from the rear of the oven) which covers the wiring. Disconnected the two leads that connect the Baking Element. Went to the front of the Oven, opened the oven door, removed the two screws with a socket wrench (you can use a screw driver as well), at this point you can replace the element with the new one and secure with the two screws. I then went back to the rear of the oven and reconnected the two wires back onto the new heating element and replaced the wiring protective back plate. Reconnected the power cord to the electrical outlet and turned on the oven to see if the element heats up. AND IT DID. Moved oven back into it's original location and I was done. This took 16 minutes to do and saved me a nice amount of money. I could have had a service person show up and do this work which would have cost me $189.00 (Parts & Labor) to have done and all I spent , by ordering the part from PARTSELECT.COM, was just under $50.00.

The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)

Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two hex head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.

Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.

I (1) pulled the oven away from the wall to get the back of it exposed. Then I (2) pulled the plug out to make sure there was no electrical current. Then I (3) opened the oven door and tugged on the broken heating element to see how tightly it was connected in the back of the oven. Next I (4) went to the back again and slid the silver-colored metal cover that protected the exposed electrical wiring for the oven. I (5) observed that there were a number of different colored wires held in place by screws as well as some wires that disappeared into the insulation, so I (6) went back to the front of the oven and pushed the broken heating element backward to determine if its wiring would become visible from the back of the stove. I (7) observed from teh back that it did. From that point, I (8) pulled the heating element's wiring connections through the insulation until it was visible. The I (9) unscrewed the two nuts connecting the heating element to the oven's wiring. Then I (10) went back to the front and pulled the broken heating element out and (11)inserted the new heating element. Then I (12) returned to the back and connected the loose wires to the heating element and (13) pushed the heating element forward into the oven. I (14) went around to the front to ensure the heating element was positioned the same way in the oven as the old one was, then in the back (15) replaced the metal shield over the wiring and isulation, (16) plugged the oven back in and (17) turned the oven baking setting on to a high temperature to test the new element (i.e., that it was connected correctly and actually worked). I (18) observed that the oven began heating up quickly to the proper temperature, and I was greateful the new bake element worked as good the original part. I then (19) turned the oven off and pushed it all the way back to its place against the wall.

The repair job was not effortless (about 15-20 minutes) but was simple enough NOT to require an electrician. The most difficult part was physically sliding the stove out and back into its tight place between our counters.

Replacing the sensor was a snap and not as involved as I feared. 1) open the oven door; 2) remove the one hex screw holding the old sensor to the back of the oven; 3) gently pull the sensor, pulling the wiring out to access the plastic wire connector (carefully guide the plastic wire connector through the opening); 4) loop a small piece of wire (stiff enough to form a hook) around the base of the wire connector to keep the wire from falling into the back wall of the oven; 5) unclip the connector and remove the bad sensor; 6) clip in the new sensor; 7) remove your catch wire; 8) thread the wiring back through the opening; 9)position the new sensor and secure with the hex screw; and 10) turn on the oven and prove to your wife you do know what you are doing!

I order the part online on the 23rd of February 09 in the afternoon it was delivered on the 24th to the address in Florida and then fedex to me in Cayman. So I got it on the 2nd of March went home that evening after work got my pliers unpluged the stove removed the two screws that holds the element in place. I also removed the metal from the back of the unit first to make sure I was doing it right. I then pulled the element at the back and disconnected the two wires replacing it with the new one. I then replaced the back and screws and pluged it in turned on the oven waited and when I saw it turn red I felt so good. I said thank you Lord and then baked a cake. The whole installation took about 20 mins.
Thanks again.
P.S. please look into offering shipping orders overseas.

The draw pictorial was not very clear. I orderd the two rear supports for the over storage draw, not sure they were correct.
They were correct and the design had been upgraded to add strength to the support.
The draw is now operational..better then ever.

Wait until oven is cold. Turn off power to the oven at the breaker panel (confirm: clock will be off). Open oven door. Remove upper rack. Unscrew glass cover over lamp and socket (it only turns one direction and may be tight). Slide cover off lamp socket. Remove old lamp - pull straight down. Install replacement lamp. Lamp pins line up front to back. Do not touch the lamp - use latex gloves. Make sure the lamp is fully pushed into its socket. Replace the glass cover by centering it on the socket with glass retaining tabs close to the matching areas on the metal socket. Take care not to damage the lamp. Turn the cover to lock in place. Make sure it is locked. Replace oven rack. Turn the power back on.

Pull the old one put in the new one ... took about 20 minutes

3 bolts the back comes right off and I always take a picture so you don't confuse your wires the part pops right off 2 wires and that's it test to se if it works buckle everything back up and your done

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Tried GE onoine parts department first and ordered the wrong part, then tried the customer hotline and they referred me to the right part but didn't explain that the design had been modified (the drawings had not been updated). I found an explanation on Part Select AND the parts were cheaper. Part Select sent the part, the necessary screw, and an appropriate instruction manual. Each support took less than a minute to screw in with a socket wrench.

Used a pliers to remove old bake element (2 nuts that none of our socket set would fit). Removed the back panel with screwdriver. Unattached bake element from wires. Then removed old element and put new element in, pulled new element wires through back and reattached to range. Screwed back in the oven with the pliers. Closed up the back panel with the screws.

First I shut off power to the unit. Then I removed the oven shelves. Next, I removed the two screws that hold the element in place using a socket ratchet. Then I carefully pulled the element out a few inches. I had some clothes pins with me because I read how some people had problems with the wire leads slipping back into the unit insulation. When the terminals and wire leads were exposed, I clamped the clothes pins on the wires between the leads and the oven wall so the wires could not be pulled back into the wall. Then I disconnected the wires from the old element. Next, I connected the new element to the wires, removed the clothes pins and gently nudge the element terminals back into the oven wall. Then I put the screws back to secure the element. Finally, I turn the power on and set the oven to 400 degrees. When I saw the element get red hot in a couple of minutes, I knew it was fixed. I've used it several times since then.

Turn off power to oven,remove two screws holding element in place,pull element forward approx. 1" and unplug wires,remove element. Install new element in reverse order of above.