My Orders
- Home
- J2C968WEK2WW
- Instructions
J2C968WEK2WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plastic guide Broken
9 of 25 people
found this instruction helpful.
-
NICK from Vernon, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
The Grate foot is to big for the hole.
1 of 2 people
found this instruction helpful.
-
Harold from Broadalbin, NY
- A Bit Difficult
- 15 - 30 mins
I had to drill the hole to a larger size to enable the foot to fit.
Was this helpful?
Thank you for voting!
very easy
1 of 2 people
found this instruction helpful.
-
ROBERT from CYPRESS, TX
- Really Easy
- Less than 15 mins
there were no grate pads so it was easy to add them.
Was this helpful?
Thank you for voting!
Light bulb went out,could not find replacement part.
1 of 2 people
found this instruction helpful.
-
Gregory from Pearl River, LA
- Really Easy
- Less than 15 mins
Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.
Was this helpful?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
1 of 3 people
found this instruction helpful.
-
Chelagh from Fredericksburg, VA
- Really Easy
- Less than 15 mins
Nothing technical.
Was this helpful?
Thank you for voting!
Oven will not heat
1 of 3 people
found this instruction helpful.
-
Joseph from Homosassa, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low c
... Read more
urrent igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Read less
Was this helpful?
Thank you for voting!
Broken Probe Sensor
0 of 1 people
found this instruction helpful.
-
Michael from Tucson, AZ
- Really Easy
- Less than 15 mins
Replaced it
Was this helpful?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
0 of 1 people
found this instruction helpful.
-
John from Tijeras, NM
- Really Easy
- Less than 15 mins
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this helpful?
Thank you for voting!
Leaking from front door
1 of 9 people
found this instruction helpful.
-
Gene from Simi Valley, CA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Read less
Was this helpful?
Thank you for voting!
warped burner
-
judith from boardman, OH
- Easy
- Less than 15 mins
reinstalled new one. just a little better than than the warped one.
Was this helpful?
Thank you for voting!
missing meat thermistor
-
John R from Asheville, NC
- Really Easy
- Less than 15 mins
plug in thermistor when needed
Was this helpful?
Thank you for voting!
Burners are supposed to burn with a blue flame. Two burners had yellow flames
-
Don from Port Orchard, WA
- Really Easy
- Less than 15 mins
New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.
Was this helpful?
Thank you for voting!
Our bottom drawer support broke and the bottom drawer was canted
-
Robert from Woodinville, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this helpful?
Thank you for voting!
Plastic slide for storage drawer broken.
-
James from Stuart, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this helpful?
Thank you for voting!
Oven Probe broke
-
Kathleen from Munt Laurel, NJ
- Really Easy
- Less than 15 mins
Ordered new probe
Was this helpful?
Thank you for voting!