IUD9750WS3 Whirlpool Dishwasher - Instructions

Replacing the float switch was fairly easy and straight forward. removed old using adjustable wrench and replaced.

Replacing the door links was not difficult except I needed to pull the dishwasher out and had to disconnect the water line.
reconnecting the water line was the time consuming and frustrating part. Once that was hooked up and tested, i pushed the dishwasher back in place and all is good again.

I researched the internet about this symptom on the Kenmore Elite Dishwasher and I found lots of people with the same problem. Everyone fixed it by replacing the Bi-Metal Fuse. I removed the old fuse and tested continuity and it was indeed bad. Once the new fuse arrived I tested continuity and it of course worked as expected, so that was a nice wipe of the brow. The new Bi-Metal Fuse came with a nice instruction manual. I also used a video from YouTube to help with the repair as well, but the included instructions were enough. The only thing that was not clear was the best way to attach the new wire since it was quite a bit longer than what was orginially there. So I ended up just folding it up and putting everything back together and it worked just fine. This repair was very easy as long as you are OK with cutting and stripping wires in a somewhat confined space and not being too worried that you might mess it up for good... :)

removed rack
removed one screw
removed old seal
installed new seal
installed screw

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

put new hose on, very easy.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

I removed broken mount by gently bending tabs, pressed new mount into upper dish rack, attached the spin arm and secured the mount with the screw.

A snap---it took less than 2 minutes after only a two day turnaround from ordering the part to receiving it at home..

Fantastic service. Thanks!!!!

REMEMBER TO SHUT OFF POWER _ Had to remove the screws using TORX driver on the inside door edge-- then came the hard part -- the foam insulation is glued to the inner door and the outer cover- I was able to finally separate the cover leaving the foam on the inner door. Then had to break off the foam insulation on the lower third of the door up from the bottom. I then had access to the screws holding the air inlet to the door. The screws are located so you can't get a straight shot at them and it is very difficult to get at them. These screws are hex head metric and very small. When they are removed the old air inlet will come right off. Take the new one and duct tape it in place inside the door and replace the screws. I recommend doing the outer ones first and since they are the easiest to get started, then you can fight the others a little easier. After the screws are replaced and tightened replace the lower half of the insulating foam by duct taping it to the foam that remained on the inner door. Then replace the outer cover and secure with the TORX screws. This was a time consuming and tough repair. I don't recommend it to a novice.

Removed 2 screws that fasten dishwasher to underside of countertop. Pulled dishwasher out from under the countertop for access to sides. Hooked link on door, threaded cord around 2 wheels, hooked spring to back of dishwasher, stretched spring and hooked to eye on end of link cord. I found it very difficult to hook spring to link then try and stretch spring to hole at back of dishwasher. Easier to pull spring and link towards each other and connect. Note: This link was actually different from the original. The plastic end that connects to the door actually hits the first wheel when door is closed but it doesn't seem to prevent the door from locking properly (old design was better). However, I shaved this plastic end to provide better clearance.

Just followed the YouTube video they sent with the receipt.

Followed the easy how-to video from PS. It was as easy as changing a light bulb.

First, I bought the door balance link to replace the broken links that connect to the springs.

Because I didn't have enough slack to simply pull out the dishwasher far enough to reach the springs, I had to disconnect the water line and electrical wiring.
The only reason my repair took as long as it did was because there was so little room underneath the dishwasher for disconnecting the water line. I had to buy a shorter adjustable wrench. Also, I had leaks after reconnecting the water line. I had to tighten the compression nut as far as it would go. The nut wrapped around a white substance that had been applied to the threads (I believe this is called pipe tape), which did the trick for sealing the leak.

The repair was a complete success! The parts arrived fast and the information from other customers on the the PartsSelect website was invaluable.

Followed included instructions... worked like a charm!

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

really easy to repair... no power to control panel but had power from breaker box. Followed directions that came with part, self explanatory, took 10 mins.