- Home
- IF36BNDFSF
- Instructions
IF36BNDFSF Dacor Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Guide rail on the crisper drawer had snapped off.
12 of 15 people
found this instruction helpful.
-
Gerald from Campton, NH
- Really Easy
- Less than 15 mins
I ordered a new crisper drawer from PartSelect over the internet one morning at approximately 10:00am, and the product was delivered, non-express delivery, the next day at about 4:pm. The front coverplate of the old crisper came off easily, and snapped into place on the new drawer easily. The entire repair/replacement took less than 5 min
... Read more
utes.
Service from PartSelect, from locating, to ordering, to rceiving the part could not have been simpler or more efficient. A 5 star experience.Thank you.
Service from PartSelect, from locating, to ordering, to rceiving the part could not have been simpler or more efficient. A 5 star experience.Thank you.
Read less
Was this helpful?
Thank you for voting!
Left front plastic wheel was broken
12 of 16 people
found this instruction helpful.
-
mike from holly springs, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Pop loose the plastic grate at the bottom.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel asse ... Read more mbly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
Reinstall and adjust wheel assembly.
Locate and remove the wheel leveling screw from the front bottom corner.
Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.
Lift out the wheel assembly.
Remove the Roller pin from the wheel asse ... Read more mbly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.
Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.
Reinstall and adjust wheel assembly.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water would not dispense
11 of 13 people
found this instruction helpful.
-
Emile from Oceanside, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers
First turned off the water at the valve. Next I undid the 5 screws holding the plate that holds the pump. Next disconnected the power connectors, then the water lines. Next undid the screw holding the pump, removed pump. Next, mounted the new pump to the plate, this was tricky because it has to fit kind of upside down, so you have to
... Read more
wrangle it into the proper position then align the screw hole. Next, secured it to the plate with the screw, re-connected the water lines, then the power. Before mounting it back to the fridge, I tested to see if it worked, well, it didn't. My heart sank. I re-checked all connections, I redid the entire process, disconnected and re-connected and still did not work. I researched the problem online and someone posted maybe the water filter might be clogged or defective. So I removed the water filter and put the stop plug in, and it worked perfectly. I went and exchanged the filter and plugged it in and still had the same problem. I am now suspecting the filter receptacle is the fault, but we will do without that for the time being. But the pressure is much better so changing the pump was still necessary. All in all a very interesting repair. I learned a lot about how the system works and now I need to replace the damper, it is very noisy.
Read less
Was this helpful?
Thank you for voting!
Refrigerator Ice Maker stopped making ice.
18 of 34 people
found this instruction helpful.
-
Harold from Oakton, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from
... Read more
the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!
Read less
Was this helpful?
Thank you for voting!
Remove the water filter to install the bypass cap
11 of 14 people
found this instruction helpful.
-
Phil from GREENFIELD, IN
- Very Easy
- Less than 15 mins
-
Pliers
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
Was this helpful?
Thank you for voting!
Leaking water tube connector/union
10 of 12 people
found this instruction helpful.
-
Roderick from NEWTOWN, PA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Received the union I ordered, then discovered that the tubes were different sizes, so I had the wrong part. I had read elsewhere that it was necessary to trim the two ends of the tubes with a box cutter to stop the leaks - I did this, and the leaking stopped. I was then able to go to a local hardware store and get a 5/16 to 1/4 union and
... Read more
replace it. The leaking is stopped, and the water supply in the door is now working like new. No problem with partselect, but I did buy a caliper so that I can check tube diameters if I ever have a similar problem! This is a great site to find instructions - well worth the time to search!
Read less
Was this helpful?
Thank you for voting!
Cracked plastic on pantry drawer lid
10 of 12 people
found this instruction helpful.
-
Angela from Bay Village, OH
- Really Easy
- Less than 15 mins
Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!
Was this helpful?
Thank you for voting!
A friend dropped a jar of relish on the plastic window and cracked it.
9 of 10 people
found this instruction helpful.
-
Gene from Petaluma, CA
- Really Easy
- Less than 15 mins
Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Was this helpful?
Thank you for voting!
There was no light on in refrig area
12 of 19 people
found this instruction helpful.
-
Lori from Chuluota, FL
- Easy
- Less than 15 mins
-
Screw drivers
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.
But Parts Select is a great place to order from. Thank you.
Was this helpful?
Thank you for voting!
Right hand door would not auto close.
16 of 31 people
found this instruction helpful.
-
Bill from Murphy, NC
- Easy
- Less than 15 mins
-
Nutdriver
Removed the top door hinge cover.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the insi ... Read more de of the door's lower hinge assembly.
Remover the four 12mm hex screws.
Lifted empty door off bottem hinge support.
Removed old door closure.
Put some silicon lub on the new closure and installed.
Reversed the removal steps.
But this did not fix the problem. Will have to remove the door and inspect the insi ... Read more de of the door's lower hinge assembly.
Read less
Was this helpful?
Thank you for voting!
Light switch rocker broke, disabling freezer internal light, water dispenser, and ice dispenser
10 of 14 people
found this instruction helpful.
-
Kenneth from Newton Grove, NC
- Really Easy
- Less than 15 mins
Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.
Was this helpful?
Thank you for voting!
Broken drawer lid
8 of 8 people
found this instruction helpful.
-
Rolf from Stanhope, NJ
- Really Easy
- Less than 15 mins
Removed broken lid and snapped new one in place.
Was this helpful?
Thank you for voting!
broken light switch
12 of 20 people
found this instruction helpful.
-
Richard from West Warwick, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
followed the instructions provided and that's it!
Was this helpful?
Thank you for voting!
Ice maker leaked water
10 of 15 people
found this instruction helpful.
-
Robert from Pennsylvania Furnace, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector
... Read more
was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.
Read less
Was this helpful?
Thank you for voting!
Refrigerator wouldn't cool
10 of 15 people
found this instruction helpful.
-
Fidel from Forest, MS
- Easy
- 30 - 60 mins
-
Screw drivers
First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.
Was this helpful?
Thank you for voting!