GTW21B2L-P1192901WL Amana Refrigerator - Instructions

Pulled out old gasket. Removed inner door molding then fixed new gasket around the edges. Replaced screws around entire inner door and snugged gasket into place. Unfortunately, it seems that the new gasket's magnets were not so strong and the door tends to pop open easily. I suppose it is better than it was...we'll need to keep an eye on it and perhaps get a manual latch of some sort....

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I recently bought an old Amana refrigerator for my garage on CraigsList for 75 bucks. It was in great condition for its age, but was missing the post that supports the fruit and veggie crisper drawers. I did a Google search, quickly found PartSelect, and just as quickly located and ordered the missing part, which was reasonably priced. PartSelect promised it woud be delivered in 3-5 days by FedEx Ground and it was. I took it out of the box, removed the crisper backets - and glass cover for them - installed the post and WHA-LA, the crisper backets work just as good as when the fridge was new! Couldn't have had an on-line mal-order operation go any slicker!

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Installed missing spacer

Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

First removed door, then removed all screws, then removed inside door panel, then removed old gasket, then installed new gasket, then reattached inside door panel and all screws, then reattached door, then used hair dryer to get gasket to seal in several areas.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

The old piece had broken off, so no removal of the old part was necessary.

New post snapped right into place, no tools required.

Total time for repair was less than two minutes.