GTDP490ED2WS General Electric Dryer - Instructions

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.

inserted the lint catcher into the opening to replace the old one

this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.

I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair

Key starting point is to remove top cover by removing two long screws located at the front of the cover
Remove control panel and it's bottom and side supports.
Remove short vent pipe by bending retainer tab.
Support the drum at the top using piece of rope.
Remove main rear cover (leave bottom attached).
Remove electric heating unit and install new bearing carrier from kit.
Reinstall the the heating unit
Remove three screws (inside the drum)to release the inner drum cover and release the bearing carrier.
Install new bearing carrier. Note: the three holes in the bearing carrier are not tapped, I suggest that the screws be installed (threads cut) into the bearing cover before attempting to install the bearing carrier.
Install the new bearing carrier. Note: pilot one of the holes using a small nail etc. then go on to install screws in the other two holes remove the pilot device and install the third screw.
Reassemble in reverse order.

After speaking with your representative and him explaining how to me how simple it would be to switch out this light socket myself. I went on y tube went through the instructions and had to go buy a new dryer. And before you jump to any conclusions I can and do repair and and all of things around my house. I will NEVER purchase anything from you company again ander the pretense that it is so simple. This should have been told to me that an election should have done the job!!!!!! Now not only am I out the money I paid your company but I’m out the money I shelled out for a whole new dryer. I am a very angry customer and I would never recommend you to anyone!!! EVER!!!

Frozen timer
1. Remove three screws from back of dryer
2. Tilt top panel forward and disengage
3. Swapped wiring one by one from old timer to new timer
4. Reinstall

This was so simple and quick. The instructions came with my order email and were as listed above and that easy.

All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.

Pulled old knob off. Aligned new knob. Pushed on. Took less than 1 minute, no tools required.
Expensive for a knob.
But it fixed the problem better than switching another knob from the machine.

easy to fix took less than 10 minutes

Didn't get to do repair because we were sent the wrong part number. Part number on box was correct but part in box was different number. So I had to pay $11.00 to send part back for refund plus original shipping of $10.00. So I'm out over $20 an still have no part to repair my dryer.

Snapped right into place , less than a minute, if that

Easy peasey! Just Removed/Replace screw-in type bulb.

Easy as 1 2 3.
1 Ordered Part Received in 3 days Great Service
2 Used Scissors to open the package (not tough to do)
3 Used 1 hand to put the knob on Works Great !!!
Start to Finish 3 min. 16 seconds !!!!

Old handle popped out by pulling back and out. Inserted new handle by pushing in and forward. Easy!