GTD72GBPN0DG General Electric Dryer - Instructions

very easy

Your site offered a video tutorial that removed any anxiety about doing the repair correctly. Removed front of dryer, disconnected wire assembly going to the front, replaced seal in seconds, returned dryer to original set up. simple. luckily. very easy to use website.

Watch the video on how to replace the belt on PartSelct site belt installation page.

The repair was easy. First I took out 2 screws. Then I lifted off the top. Next I unscrewed 2 to take off front. I leaned off the front and reached in got out old gasket. Replacing new gasket went right around top front panel under the clips. Putting front on and returning 2 screws. Then Same for top. Dryer runs and sounds like new. Thank You for your quick mail and easy help?

Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.

replaced felt on inside door that drum rides on

I used these two videos to help me clean the inside of the machine, then change the drive belt.

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Unplug the dryer. On the back, I unscrewed the top three screws that hold on the instrument panel and (from the back) slide the panel to my left to disconnect from the top. I opened the dryer door and removed the two screws on the inside top of the doorway to remove the top panel of the dryer. Inside the top of the dryer are two screws to remove so that I could swing the front panel of the dryer out to replace the lower front felt drum seal. I needed to use wd-40 on these screws. When the panel opens, there is no way to disconnect the wires to remove the panel, so I had to prop it up with something so it didn't tip over and damage the wiring; a sturdy chair worked. Then, I heared the drum pop off and drop down a little. I replaced the seal according to the video; by putting it in the groove and pressing it down into the tabs with a flat head screwdriver or something smooth with a little of the seal hanging over the groove at each end. While I was in there, I cleaned out the lint and the wd-40 I used earlier. Then I closed the panel, lifting the drum back into place, ensuring that the dryer drum would turn before and after I replaced the screws. I replaced the top panel and the screws inside the dryer door and slid the instrument panel back into place and replaced those screws. The dryer works great and very quietly now!

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes