GTD65EBSJ0WS General Electric Dryer - Instructions

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Unplug the dryer. On the back, I unscrewed the top three screws that hold on the instrument panel and (from the back) slide the panel to my left to disconnect from the top. I opened the dryer door and removed the two screws on the inside top of the doorway to remove the top panel of the dryer. Inside the top of the dryer are two screws to remove so that I could swing the front panel of the dryer out to replace the lower front felt drum seal. I needed to use wd-40 on these screws. When the panel opens, there is no way to disconnect the wires to remove the panel, so I had to prop it up with something so it didn't tip over and damage the wiring; a sturdy chair worked. Then, I heared the drum pop off and drop down a little. I replaced the seal according to the video; by putting it in the groove and pressing it down into the tabs with a flat head screwdriver or something smooth with a little of the seal hanging over the groove at each end. While I was in there, I cleaned out the lint and the wd-40 I used earlier. Then I closed the panel, lifting the drum back into place, ensuring that the dryer drum would turn before and after I replaced the screws. I replaced the top panel and the screws inside the dryer door and slid the instrument panel back into place and replaced those screws. The dryer works great and very quietly now!

As I pulled each of the 3 bolts, I put a alignment rod into each of the holes. After I pulled the old deflector off, I had basically 3 pins/rods to slip the new deflector on and keep everything in basic alignment. Pulled one rod, reinstalled the bolt, so on and so on. Ran motor for noises or misalignment and had neither. Pretty simple repair.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes

I'm a 90 pound mother of 4you and was able to fix this problem all by myself. Very easy!

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

My son ordered the part, but gave up installing it. We called in a professional appliance repairman because the dryer had to be partially dismantled to remove the drum and a belt so three sets of holes could be aligned to secure the replacement diffuser. My daughter had to lend a hand to hold one piece in place while the repairman threaded the screws because the drum was too deep for him to be able to reach both front and back pieces. Definitely not a one-person job for this particular model.

Followed the directions from the video about that particular part. I am 57 and it was fairly simple to do.